Atmel ATSAML22G16A-AUT Manual Download Page 208 | Manualshive

Page: 208 / 1231

background image

21.3. Block Diagram

Figure 21-1. OSCCTRL Block Diagram

OSCILLATORS

CONTROL

STATUS

INTERRUPTS

GENERATOR

Interrupts

OSCCTRL

XIN

XOUT

XOSC

OSC16M

DFLL48M

DPLL96M

CLK_XOSC

CLK_OSC16M

CLK_DFLL48M

CLK_DPLL

CFD

CFD Event

register

21.4. Signal Description

Signal

Description

Type

XIN

Multipurpose Crystal Oscillator or external clock generator input

Analog input

XOUT

Multipurpose Crystal Oscillator output

Analog output

The I/O lines are automatically selected when XOSC is enabled.

21.5. Product Dependencies

In order to use this peripheral, other parts of the system must be configured correctly, as described below.

21.5.1. I/O Lines

I/O lines are configured by OSCCTRL when XOSC is enabled, and need no user configuration.

21.5.2. Power Management

The OSCCTRL can continue to operate in any sleep mode where the selected source clock is running.
The OSCCTRL interrupts can be used to wake up the device from sleep modes. The events can trigger
other operations in the system without exiting sleep modes.

Related Links

PM – Power Manager

21.5.3. Clocks

The OSCCTRL gathers controls for all device oscillators and provides clock sources to the Generic Clock
Controller (GCLK). The available clock sources are: XOSC, OSC16M, DFLL48M, and FDPLL96M.

The OSCCTRL bus clock (CLK_OSCCTRL_APB) can be enabled and disabled in the Main Clock module
(MCLK).

The DFLL48M control logic uses the DFLL oscillator output, which is also asynchronous to the user
interface clock (CLK_OSCCTRL_APB). Due to this asynchronicity, writes to certain registers will require
synchronization between the clock domains. Refer to

Synchronization

for further details.

Atmel SAM L22G / L22J / L22N [DATASHEET]

Atmel-42402E-SAM L22G / L22J / L22N_Datasheet_Complete-07/2016

208

«
...
206
207
208
209
210
...
»

Summary of Contents for ATSAML22G16A-AUT
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ATSAML22G16A-AUT

HmIP-FAL230-C10

Brand: HomeMatic Pages: 42

Brand: Ros Pages: 10

Brand: Festo Pages: 109

Brand: Topworx Pages: 8

Brand: AUMA Pages: 24

Brand: intech 21 Pages: 15

Brand: Ezodo Pages: 7

VENMAR ADVANCED TOUCHSCREEN CONTROL

Brand: vanEE Pages: 4

Brand: GOAL ZERO Pages: 52

Brand: Jetter Pages: 62

Brand: Continental Instruments Pages: 2

Brand: InnoMedia Pages: 10

AGCO RoGator Hawkeye C Series

Brand: Raven Pages: 64

Automation PC 620

Brand: B&R Pages: 594

Brand: Analog Devices Pages: 312

Brand: Viking Electronics Pages: 12

Brand: Hamworthy Pages: 108

Duomatic L Plus

Brand: Truma Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands