Atmel ATSAML22G16A-AUT Manual Download Page 223 | Manualshive

Page: 223 / 1231

background image

Offset

Name

Bit Pos.

0x2C

7:0

LDR[7:0]

0x2D

15:8

LDR[11:8]

0x2E

23:16

LDRFRAC[3:0]

0x2F

31:24

0x30

7:0

REFCLK[1:0]

WUF

LPEN

FILTER[1:0]

0x31

15:8

LBYPASS

LTIME[2:0]

0x32

23:16

DIV[7:0]

0x33

31:24

DIV[10:8]

0x34

7:0

PRESC[1:0]

0x35

...

0x37

Reserved

0x38

7:0

DPLLPRESC DPLLRATIO

ENABLE

0x39

...

0x3B

Reserved

0x3C

7:0

CLKRDY

LOCK

21.8. Register Description

Registers can be 8, 16, or 32 bits wide. Atomic 8-, 16-, and 32-bit accesses are supported. In addition,
the 8-bit quarters and 16-bit halves of a 32-bit register and the 8-bit halves of a 16-bit register can be
accessed directly.

Some registers are optionally write-protected by the Peripheral Access Controller (PAC). Write-protection
is denoted by the "PAC Write-Protection" property in each individual register description. Refer to the

Register Access Protection

section and the

PAC - Peripheral Access Controller

chapter for details.

Some registers require synchronization when read and/or written. Synchronization is denoted by the
"Read-Synchronized" or "Write.Synchronized" property in each individual register description. Refer to the

Synchronization

section for details.

Atmel SAM L22G / L22J / L22N [DATASHEET]

Atmel-42402E-SAM L22G / L22J / L22N_Datasheet_Complete-07/2016

223

«
...
221
222
223
224
225
...
»

Summary of Contents for ATSAML22G16A-AUT
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ATSAML22G16A-AUT

Brand: GE Pages: 425

Brand: Gardena Pages: 14

Brand: Gardena Pages: 4

GAT ACCESS 6100

Brand: Gantner Pages: 4

Brand: Panosol Pages: 105

Brand: Pangolin Pages: 8

Brand: YASKAWA Pages: 49

Brand: M-system Pages: 17

Brand: Zaiput Flow Technologies Pages: 10

Brand: Zero 88 Pages: 34

Brand: M-Elec Pages: 2

ACTPRO PRODUCT RANGE

Brand: ACT Pages: 8

Brand: OCL Pages: 2

Brand: QUANT Pages: 24

Brand: NEC Pages: 265

Brand: National Instruments Pages: 8

AMBITECH BRAKE-PAK

Brand: TIE Pages: 5

OPUS A3 STANDARD Full

Brand: Topcon Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands