![background image](http://html1.mh-extra.com/html/omron/cs1w-213-rev-02-2008/cs1w-213-rev-02-2008_operation-manual_742355097.webp)
72
Common Parameter Area
Section 4-2
Beginning Word of Operating Data Area (Word m+1)
If user-specified DM Area words (0D) or user-specified EM Area words (0E)
are designated as the location for the operating data area using the area des-
ignation setting (word m, bits 00 to 07), use this setting to designate the
beginning word of the operating data area. The beginning word is set in hexa-
decimal. The following settings are possible (varies with the model):
NC1
@
3: 0000 to 7FE8 Hex (0 to 32744)
NC2
@
3: 0000 to 7FD8 Hex (0 to 32728)
NC4
@
3: 0000 to 7FB8 Hex (0 to 32696)
If DM Area words allocated to Special I/O Units (00) are designated as the
location for the operating data area, this setting will not be used.
Example 1
The area in the CPU Unit’s DM Area beginning with word 1F40 Hex (8000) is
designated as the operating data area. The following words are allocated (var-
ies with the model):
NC1
@
3:D8000 to D8023
NC2
@
3:D8000 to D8039
NC4
@
3:D8000 to D8071
Example 2
The area in bank 2 of the CPU Unit’s EM Area beginning with word 3A98 Hex
(15000) is designated as the operating data area. The following words are
allocated (varies with the model):
NC1
@
3: E2_15000 to E2_15023
NC2
@
3: E2_15000 to E2_15039
NC4
@
3: E2_15000 to E2_15071
Axis Parameter Designation
Word Address and Enable
Timing
The word address and enable timing for the axis parameter designation set-
ting is shown below.
Bit Configuration
The bit configuration for the word address in the above table is shown below.
Settings
The following settings are available.
Word m+2: 0X00, 0X01 (X = 0 to 9, A to F)
Explanation
The meanings of each of the settings are given below.
Parameter Designation (Word m+2, Bits 00 to 07)
Specify the axis parameters to use during PCU operation. The following set-
tings are available.
0
m
0
0
D
1
m+1
F
4
0
0
m
2
0
E
3
m+1
9
8
A
Word
Name
Enable timing
NC1
@
3
NC2
@
3
NC4
@
3
m+2
Axis parameter designa-
tion
At power up or restart
15
00
08 07
Axis designation
Parameter designation
m+2
12 11
Specified unused axes
Содержание CS1W-213 - REV 02-2008
