![background image](http://html1.mh-extra.com/html/omron/cs1w-213-rev-02-2008/cs1w-213-rev-02-2008_operation-manual_742355343.webp)
318
Error Code Lists
Section 11-5
Initial speed
Initial speed error
1000
The axis parameters’ initial speed
setting exceeds the maximum
speed setting for an axis.
In this condition, only the data transfer
(read or write) and data save opera-
tions can be performed. In this case,
the PCU's axis parameters and data
are all returned to their default values
if the unit version of the PCU is earlier
than version 2.3. If the unit version of
the PCU is version 2.3 or later, only
parameters and data for which an
error has been detected will be
returned to their default values.
After correcting the appropriate axis
parameters, reset the power supply or
restart the PCU.
Initial pulse desig-
nation error
1001
The initial pulse designation is not
set to 0000 or 0001.
Maximum speed Maximum speed
error
1010
The axis parameters’ maximum
speed setting is outside the setta-
ble range (1 to 500 kpps).
Acceleration/
deceleration
data
Acceleration time
error
1310
The axis parameters’ origin search
acceleration time setting is outside
the settable range (0 to 250 s).
Deceleration time
error
1320
The axis parameters’ origin search
deceleration time setting is outside
the settable range (0 to 250 s).
Acceleration/
Deceleration
curve error
1330
The axis parameters’ acceleration/
deceleration curve setting is not 0
or 1.
Positioning moni-
tor time error
1332
The axis parameters’ positioning
monitor time setting is outside the
settable range (0 to 9999 ms).
Origin search
Origin compensa-
tion error
1600
The axis parameters’ origin com-
pensation setting is outside the
settable range (–1,073,741,823 to
1,073,741,823 pulses).
Origin search high
speed error
1601
The axis parameters’ origin search
high speed setting exceeds the
axis parameters’ maximum speed
setting.
Origin search
proximity speed
error
1602
The axis parameters’ origin search
proximity speed setting exceeds
the axis parameters’ maximum
speed setting.
Origin search
speed inconsis-
tent
1603
The axis parameters’ origin search
high speed setting is less than or
equal to the origin search proxim-
ity speed setting.
Operation mode
selection error
1604
The axis parameters’ origin search
operating mode selection setting is
not 0, 1, 2, or 3.
Origin search
operation error
1605
The axis parameters’ origin search
operation setting is not 0, 1, or 2.
Group
Name
Code
Cause
Remedy
Содержание CS1W-213 - REV 02-2008
