Toshiba GR 200 Series, Instruction Manual

Page: 867 / 1563

6F2S1915 (0.46)
GRZ200 (Soft 031 & 032)
- 846 -
PLC
BO4_SOURCE 200B01 310203E11D
“TPOS01_P1EX_BO”
(513001 _ 8104011DD0)
Operate logic in TPOS01
PLC connection point in BO4
Operate logic for
P1-control
in TPOS01
≥1
& [ BO4_CPL ]
Off
On
&
DRIVER BO4
Signal designated by
setting [ Input signal 1 ]
[ Input signal 2 ]
[ Input signal 3 ]
[ Input signal 4 ]
[ Input signal 5 ]
[ Input signal 6 ]
[ Input signal 7 ]
[ Input signal 8 ]
Operate
command
P1
≥1
“BO4”
(200B01 _ 8302031112)
“BO4-RB”
(200B01 _ 8302031113)
BO4
–BO6 circuit at IO#1 (Function ID: 200B01)
Terminal and
wire
To contact health
check
BO5_SOURCE
200B01 310204E11D
“TPOS01_P2EX_BO”
(513001 _ 8204011DD3)
PLC connection point in BO5
Operate logic for
P2-control
in TPOS01
≥1
&
[ BO5_CPL ]
Off
On
&
DRIVER BO5
Signal designated by
setting [ Input signal 1 ]
[ Input signal 2 ]
[ Input signal 3 ]
[ Input signal 4 ]
[ Input signal 5 ]
[ Input signal 6 ]
[ Input signal 7 ]
[ Input signal 8 ]
Operate
command
P2
≥1
“BO5”
(200B01 _ 8402041112)
“BO5-RB”
(200B01
_ 8402041113)
To contact health
check
To contact health
check
To contact health
check
Connected by
“Programming”
Connected by
“Programming”
BO6_SOURCE 200B01 310205E11D
“TPOS01_P3EX_BO”
(513001 _ 8204011DD6)
PLC connection point in BO6
Operate logic for
P3-control
in TPOS01
≥1
& [ BO6_CPL ]
Off
On
&
DRIVER BO6
Signal designated by
setting [ Input signal 1 ]
[ Input signal 2 ]
[ Input signal 3 ]
[ Input signal 4 ]
[ Input signal 5 ]
[ Input signal 6 ]
[ Input signal 7 ]
[ Input signal 8 ]
Operate
command
P3
≥1
“BO6”
(200B01
_ 8502051112)
“BO6-RB”
(200B01 _ 8502051113)
To contact health
check
To contact health
check
Connected by
“Programming”
Figure 4.9-58 Example of operate commands connected with BO4-BO2
†Note: Table 4.9-20 shows the remaining signals except for “TPOS01”.
(iv)
Contact health check
The TPOS01 function has contact health check feature for the BO circuits; hence, the user is
able to connect an output signal to the contact health check function when
Fixedlogic
is set for
scheme switches [
TPOS01- LGP1EXOT
] to [
TPOS01-LGP3EXOT
]†. Consequently, the TPOS01
function can determine whether the signal has been successfully output from the BO. If a
failure is reported, the TPOS01 function determines that the signal is not output successfully
to the BO; then the command is canceled immediately and the TPOS01 function returns to the
“Wait for a command” stage.
†Note: Table 4.9-21 shows settings for the health check feature in the other TPOS
functions.
Setting for “select command P1/P2/P3”
For example, the point”TPOS01_P1SL_BO” is connected to the BO1 circuit for the issuing of