manualshive.com logo in svg

Sharp AR-BC320, Service Manual, Page: 70 / 344

Share
Download
Sharp AR-BC320 Service Manual Download Page 70

AR-BC320  DESCRIPTIONS OF EACH SECTION  7 - 29

b. Manual paper feed section

(3) Major parts and signals functions and operations

a. Manual paper feed unit

RW: Abbreviation of Related Wiring, which means the said load is specified in the related figure of the mechanical and the electrical sections.

GND2

GND2

GND2

DSWR

DSWRout

CN11(34pin)

(8pin)

(2pin)

(14pin)

CN17(28pin)

+5V

+5V

+24V

+24V

+24V

+3.3V

MPFC\

+24V

MPFC\

DC_ONOFF\

DC_LOCK\

DC_CLK

GND2

+24V

DC_ONOFF\

DC_LOCK\

DC_CLK

MPED

MPED

MPWSin

GND2

+3.3V

MPWSin

MTOP2

MTOP1

MPLD1

MPLD2

MT

OP2

MT

OP1

MPLD1

MPLD2

MTRC\

+24V

MTRC\

HUMiD_AN

TEMP_AN

GND2

GND2

GND2

GND2

GND2

+5V

+5V

+5V

HUD

TEMP

PCU

MTRC

MPED

MPWS

HUD

MTOP2

MPLD2

MPLD2

MPLD1

MPLD1

PFM

Paper feed motor

Right door switch

Paper length
sensor 1

Paper width
sensor

Manual transport clutch

DSWR

8

8

9

10

11

11

12

13

13

14

14

15

16

17

18

19

20

30

34

24

28

25

23

21

22

7

7

7

7

6

6

5

5

5

4

4

4

3

3

3

3

3

2

2

2

1

1

1

1

3

3

3

3

3

2

2

2

2

2

2

2

2

2

1

1

1

1

1

1

1

1

1

2

1

Tray position 
detection switch 2

Paper length
sensor 2

MPFC

Manual paper feed clutch

Humidity sensor

MTOP1

Tray position
detection 
switch 1

No.

Name

Code, Signal name

Function

RW

Paper detector

MPED

Detects paper empty/presence in the paper tray.

1

Paper size (width) adjuster

—

Adjusts the paper position.

2

Paper size (width) sensor

MPWS

Detects the paper width.

3

Paper size (length) detector

MPLD1

Detects the paper length.

4

Paper size (length) detector

MPLD2

Detects the paper length.

5

Tray position detector

MTOP1

Detects the paper tray position.

6

Tray position detector

MTOP2

Detects the paper tray position.

7

Paper pickup roller

—

Sends paper to the paper feed roller.

8

Manual paper feed roller

—

Feeds paper to the paper transport section.

9

Manual paper feed clutch

MPFC

Transmits the paper feed drive motor power to the manual paper feed roller.

10

Separation roller

—

Separates paper and transmits it to the paper feed unit.

RW

Manual transport clutch

—

Transmits the paper feed motor power to the manual paper feed unit.

RW

Paper feed motor

—

Drives the paper feed section and the manual paper feed unit.

1

1

6

8

7

2

3

4

5

10

10

8

7

9

Summary of Contents for AR-BC320

























































































































































































































































































































































Reviews:

No comments