manualshive.com logo in svg

Sharp AR-BC320, Service Manual, Page: 193 / 344

Share
Download
Sharp AR-BC320 Service Manual Download Page 193

AR-BC320  SIMULATION  9 - 39

∗

The B/W start key or the color start key can be used instead of 
the [OK] key in the above procedure.

(Trial mode setting)

(Toner save mode setting)

[Target item]

∗

Maintenance preset counter (Depending on the set value of 
SIM21-1.)

∗

Consumable part replacement timing

Transfer belt (Depending on the set value of SIM21-1.)

Fusing unit (Depending on the set value of SIM21-1.)

OPC drum

When the toner cartridge is emptied, printing is stopped regardless 
of this setup.

26

-10

Purpose

Setting

Function 
(Purpose)

Used to set the trial mode of the network scanner.

Section

Scanner

Item

Specifications

Operation/
Procedure

1. Set ON/OFF of the trial mode with the 10-key 

pad, and press the [OK] key.

Item

Content

Set range

Default

A

Trial mode setting

0: NO
1: YES

0

26

-18

Purpose

Setting

Function 
(Purpose)

Used to set YES/NO of toner save operation. 
(This simulation is Enable only for Japan and UK 
versions. It depends on SIM 26-6 (Destination) 
setting.
For the other destinations, the same setting can be 
made by the user program P22. (Effective only in 
the monochrome copy mode)

Item

Specifications

Operation mode (Common)

Operation/
Procedure

Enter the code number corresponding to the 
condition (the toner save YES/NO) with the 10-key 
and press the [OK] Key.

Item

Content

Set range

Default

A

COPY
(0:NO 1:YES)

Copy mode toner 
save mode inhibit

0:NO
1:YES

0

B

NO  USE

—

—

—

C

PRINTER
(0:NO 1:YES)

Printer mode toner 
save mode inhibit

0:NO
1:YES

0

26

-35

Purpose

Setting

Function 
(Purpose)

Used to set whether the trouble history display by 
SIM 22-4 is displayed as one trouble or as the 
accumulated number of continuous troubles when 
two or more troubles of same kind occur 
continuously.

Item

Specifications

Operation/
Procedure

Used to set whether the trouble history display by 
SIM 22-4 is displayed as one trouble or as the 
accumulated number of continuous troubles when 
two or more troubles of same kind occur 
continuously.
1. Select the number corresponding to the display 

mode with the 10-key and press the [OK] key.

Item

Set value

Default

The trouble history display by SIM 22-4 is 
displayed as it is when two or more 
troubles occur continuously.

1

0

The trouble history display by SIM 22-4 is 
displayed as one trouble when two or 
more troubles occur continuously.

0

26

-38

Purpose

Setting

Function 
(Purpose)

Used to set "Continue/Stop" of printing when the 
maintenance timing (replacement timing of each 
consumable part) is reached.

Item

Specifications

Operation/
Procedure

When the maintenance timing (replacement timing 
of each consumable part) is reached, set "Continue/
Stop" of printing by entering the code number with 
the 10-key, referring to the table below. Then press 
the [OK] key.

Item

Content

Set value

Default

A (0:CONTINUE 

1:STOP)

Used to set 
"Continue/Stop" of 
printing when the 
maintenance timing 
(replacement timing 
of each consumable 
part) is reached.

0 Continues 

printing.

0

1 Stops 

printing.

26

-41

Purpose

Setting

Function 
(Purpose)

Used to set Enable/Disable of AMS operation in the 
center-binding mode.

Item

Specifications

Summary of Contents for AR-BC320

























































































































































































































































































































































Reviews:

No comments