Sharp AR-BC320, Service Manual, Page: 216 / 344

AR-BC320 SIMULATION 9 - 62
2. Enter the adjustment value of the selected point with the 10-
key, and press the [OK] key. (The entered adjustment value is
set. The [EXECUTE] key or the scroll key can be used instead
of the [OK] key in the above procedure.)
3. Press the [EXECUTE] key. The test pattern corresponding to
the entered adjustment value is printed.
• When the adjustment value of items A~G is decreased by 1, the
main scanning print position shifts 0.1mm toward the front side.
• When the adjustment value of items A~G is increased by 1, the
main scanning print position shifts 0.1mm toward the rear side.
• To execute item G (ADU adjustment), the ADU must be
installed. In this case, item K (DUPLEX) must be set to 2.
∗
When the set value is increased, the image is shifted to the rear
side.
When the set value is decreased, the image is shifted to the
front side.
(Items to be set)
2. Enter the adjustment value of the selected point with the 10-
key, and press the [OK] key. (The entered adjustment value is
set.)
3. Press the [EXECUTE] key, and the registration adjustment
pattern in the main scanning direction is printed.
(Set items)
∗
When the adjustment value of items A, C, and E is decreased
by 1, the adjustment target color image shifts by one pixel in the
main scanning direction.
∗
When the adjustment value of items B, D, and E is decreased
by 1, the adjustment target color image shifts by one pixel in the
sub scanning direction.
Display Content Set range Default
A MFT Print off-center adjustment
value (Manual paper feed) 1 – 99 50
B CS1 Print off-center adjustment
value (1 cassette) 1 – 99 50
C CS2 Print off-center adjustment
value (2 cassette) 1 – 99 50
D CS3 Print off-center adjustment
value (3 cassette) 1 – 99 50
E CS4 Print off-center adjustment
value (4 cassette) 1 – 99 50
F LCC Print off-center adjustment
value (LCC) 1 – 99 50
G ADU Print off-center adjustment
value (ADU) 1 – 99 50
H MULTI
COUNT Print quantity 1 – 999 1
I PAPER Paper feed tray selection
(MFT, CS1, CS2, CS3,
CS4, LCC) 1 – 6 2 (CS1)
J EXIT
TRAY Paper exit tray selection
(R, S) 1 or 2 1
K DUPLEX Duplex print selection
(NO, YES) 1 or 2 1
50 -12
Purpose Adjustment
Function
(Purpose) Used to adjust the print image center position. (The
adjustment is performed in each document mode
separately.)
Section Image process (ICU)
Item Picture quality Image position
Operation/
Procedure 1. Select the adjustment mode with the scroll key.
2. Enter the adjustment value with the 10-key and
press the [OK] key to set the entered value.
Display Content
Min.
Value
Max.
Value
Default
A OC Platen mode (Document
table) 1 99 50
B ADF RADF mode 1 99 50
50 -20
Purpose Adjustment
Function
(Purpose) Used to adjust the image registration. (Manual
adjustment)
Item Picture quality Image position
Operation/
Procedure 1. Select the adjustment mode (DEN-B/DEN-C)
with the scroll key.
Display Content
Min.
value
Max.
value
Default
A MAIN-
REGIST C Main scanning
direction registration
adjustment (C) 12 88 50
B SUB-
REGIST C Sub scanning
direction registration
adjustment (C) 1 132 50
C MAIN-
REGIST M Main scanning
direction registration
adjustment (M) 12 88 50
D SUB-
REGIST M Sub scanning
direction registration
adjustment (M) 1 132 50
E MAIN-
REGIST Y Main scanning
direction registration
adjustment (Y) 12 88 50
F SUB-
REGIST Y Sub scanning
direction registration
adjustment (Y) 1 132 50
G MULTI
COUNT Adjustment pattern
print quantity 1 999 1
H PAPER Paper feed tray
selection (MFT,
CS1, CS2, CS3,
CS4, LCC) 1 6 2 (CS1)
I EXIT
TRAY Paper exit tray
selection (R, S) 1 2 1
J DUPLEX Duplex print
selection (NO, YES) 1 2 1