manualshive.com logo in svg

Sharp AR-BC320, Service Manual, Page: 270 / 344

Share
Download
Sharp AR-BC320 Service Manual Download Page 270

AR-BC320  TROUBLESHOOTING  11 - 23

Main 
code

Sub 

code

Title

RTC read trouble

U1

02

Display

Lamp/Message

Phenomenon Detail

Abnormal value is read 
from the RTC on the ICU 
PWB.

Section

—

Case 1

Cause

RTC circuit abnormality

Check & 
Remedy

Set the time again with the 
key operation, and check 
that time advances 
properly.
Check the RTC circuit.

Main 
code

Sub 

code

Title

EEPROM read/write error (ICU 
detection)

U2

00

Display

Lamp/Message

Phenomenon Detail

EEPROM version error
EEPROM write error

Section

—

Case 1

Cause

EEPROM trouble. 
EEPROM is not initialized.

Check & 
Remedy

1. Check that the 

EEPROM is properly 
set.

2. Use SIM 16 to cancel 

the error.

Case 2

Cause

ICU PWB EEPROM 
access circuit trouble

Check & 
Remedy

1. To prevent against 

deletion of the counter 
data and the adjustment 
data, record them with 
the simulation. (When a 
printer option is 
installed, use SIM 22-1 
to record the counter 
data and the adjustment 
data.)

2. Replace the ICU PWB.
3. Use SIM 16 to cancel 

the error.

Main 
code

Sub 

code

Title

EEPROM check sum error (ICU 
detection)

U2

11

Display

Lamp/Message

Phenomenon Detail

EEPROM (ICU) check sum 
error

Section

—

Case 1

Cause

EEPROM trouble

Check & 
Remedy

1. Check that the 

EEPROM is properly 
set.

2. Use SIM 16 to cancel 

the error.

Case 2

Cause

Control circuit freeze by 
noises.
ICU PWB EEPROM 
access circuit trouble.

Check & 
Remedy

1. To prevent against 

deletion of the counter 
data and the adjustment 
data, record them with 
the simulation. (When a 
printer option is 
installed, use SIM 22-1 
to record the counter 
data and the adjustment 
data.)

2. Replace the ICU PWB.
3. Use SIM 16 to cancel 

the error.

Main 
code

Sub 

code

Title

Production No. data discrepancy 

U2

30

Display

Lamp/Message

Phenomenon Detail

The production No. 
recorded in the PCU differs 
from that recorded in the 
ICU.

Section

—

Case 1

Cause

EEPROM is not 
exchanged when replacing 
the PCU/ICU PWB.

Check & 
Remedy

Check that the EEPROM is 
properly installed. When 
replacement, check that 
the EEPROM before 
replacement is inserted to 
the board after 
replacement.

Summary of Contents for AR-BC320

























































































































































































































































































































































Reviews:

No comments