manualshive.com logo in svg

Sharp AR-BC320, Service Manual, Page: 197 / 344

Share
Download
Sharp AR-BC320 Service Manual Download Page 197

AR-BC320  SIMULATION  9 - 43

(Sensors to be checked)

(Sensors to be checked)

2. Press the [EXECUTE] key. The [EXECUTE] key is highlighted 

then it returns to the normal display. The manual paper feed 
guide max. width position detection level is recognized.

3. Set the manual paper feed guide to A4 (11 x 8.5") size.
4. Press the [EXECUTE] key. The key is highlighted then it 

returns to the normal display. The manual paper feed guide A4 
(11 x 8.5") detection level is recognized.

5. Set the manual paper feed guide to A4R (11 x 8.5R) size.
6. Press the [EXECUTE] key. The key is highlighted then it 

returns to the normal display. The manual paper feed guide A4 
R (11 x 8.5"R) detection level is recognized.

7. Set the manual paper feed guide to the minimum size.
8. Press the [EXECUTE] key. The key is highlighted then it 

returns to the normal display. The manual paper feed guide 
minimum size detection level is recognized.
If the above operation is not performed properly, the ERROR 
display is highlighted. If performed properly, the above data is 
stored and the COMPLETE is highlighted.

30

-2

Purpose

Operation test/check

Function 
(Purpose)

Used to check the operation of sensors and 
detectors in the paper feed section and the related 
circuits. (The operation of the paper feed sensors 
and detectors can be monitored with the LCD 
display.)

Section

Paper feed

Item

Operation

Operation/
Procedure

The active sensors and detectors are highlighted.

Sensor name

Content

LUD1

Paper feed tray upper limit detection (Tray 1)

PED1

Paper feed tray paper empty detection (Tray 1)

C1PD1

Paper feed tray remaining paper quantity 
detection (Tray 1)

C1SS1

Paper feed tray size detection 1 (Tray 1)

C1SS2

Paper feed tray size detection 2 (Tray 1)

C1SS3

Paper feed tray size detection 3 (Tray 1)

C1SS4

Paper feed tray size detection 4 (Tray 1)

MPLD1

Manual feed size length detection 1

MPLD2

Manual feed size length detection 2

MTOP1

Manual feed tray pull-out detection 1

MTOP2

Manual feed tray pull-out detection 2

MPED

Manual feed tray paper empty detection

33

33

-1

Purpose

Operation test/check

Function 
(Purpose)

Used to check the operation of the card reader and 
the sensors and the related circuits. (The card 
reader sensor operation can be monitored with the 
LCD display.)

Section

Others

Item

Operation

Operation/
Procedure

Active/Inactive of the card reader is displayed.

Sensor name

Content

CARD

Card insertion detection 

DATA

Card number signal detection

CLOCK

Reference clock signal detection

40

40

-1

Purpose

Operation test/check

Function 
(Purpose)

Used to check the operation of the manual feed tray 
paper size detector and the related circuit. (The 
operation of the manual feed tray paper size 
detector can be monitored with the LCD display.)

Section

Paper feed

Item

Operation

Operation/
Procedure

The active sensors and detectors are highlighted.
Press the [CLOSE] key to terminate the simulation.

MPLD1

Manual feed size length detection 1

MPLD2

Manual feed size length detection 2

MTOP1

Manual feed tray pull-put detection 1

MTOP2

Manual feed tray pull-out detection 2

40

-2

Purpose

Adjustment

Function 
(Purpose)

Used to adjust the manual feed tray paper width 
detector detection level.

Section

Paper feed

Item

Operation

Operation/
Procedure

1. Set the manual paper feed guide to the 

maximum size.

Summary of Contents for AR-BC320

























































































































































































































































































































































Reviews:

No comments