manualshive.com logo in svg

Sharp AR-BC320, Service Manual, Page: 261 / 344

Share
Download
Sharp AR-BC320 Service Manual Download Page 261

AR-BC320  TROUBLESHOOTING  11 - 14

Main 
code

Sub 

code

Title

Developing unit CRUM trouble 
(Cyan)

F2

75

Display

Lamp/Message

Phenomenon Detail

CRUM read/write error

Section

Developing

Case 1

Cause

Improper connection or 
disconnection of the 
connector and the harness 
between the PCU and the 
CRUM.

Check & 
Remedy

Check the connector and 
the harness between the 
PCU and the CRUM.

Case 2

Cause

Developing unit trouble

Check & 
Remedy

Replace the developing 
unit.

Case 3

Cause

Control PWB (PCU) 
trouble

Check & 
Remedy

Replace the PCU PWB.

Main 
code

Sub 

code

Title

Developing unit CRUM trouble 
(Magenta)

F2

76

Display

Lamp/Message

Phenomenon Detail

CRUM read/write error

Section

Developing

Case 1

Cause

Improper connection or 
disconnection of the 
connector and the harness 
between the PCU and the 
CRUM.

Check & 
Remedy

Check the connector and 
the harness between the 
PCU and the CRUM.

Case 2

Cause

Developing unit trouble

Check & 
Remedy

Replace the developing 
unit.

Case 3

Cause

Control PWB (PCU) 
trouble

Check & 
Remedy

Replace the PCU PWB.

Main 
code

Sub 

code

Title

Developing unit CRUM trouble 
(Yellow)

F2

77

Display

Lamp/Message

Phenomenon Detail

CRUM read/write error

Section

Developing

Case 1

Cause

Improper connection or 
disconnection of the 
connector and the harness 
between the PCU and the 
CRUM.

Check & 
Remedy

Check the connector and 
the harness between the 
PCU and the CRUM.

Case 2

Cause

Developing unit trouble

Check & 
Remedy

Replace the developing 
unit.

Case 3

Cause

Control PWB (PCU) 
trouble

Check & 
Remedy

Replace the PCU PWB.

Main 
code

Sub 

code

Title

Trouble of image density sensor 
for registration (Transfer belt 
surface reflection ratio 
abnormality)

F2

78

Display

Lamp/Message

Phenomenon Detail

Before starting registration, 
the transfer belt surface is 
scanned with the image 
density sensor to adjust 
the sensor gain so that the 
output becomes a fixed 
value. However, when the 
sensor gain is changed, 
the value is not within the 
specified range.

Section

—

Case 1

Cause

Image density sensor 
trouble, disconnection of 
the harness between the 
PCU PWB and the image 
density sensor, dirt on the 
image density sensor.

Check & 
Remedy

Check the sensor and the 
harness.

Case 2

Cause

Calibration plate solenoid 
operation trouble

Check & 
Remedy

Check the calibration plate 
solenoid operation.

Case 3

Cause

Insufficient cleaning of the 
transfer belt.

Check & 
Remedy

Check the transfer belt 
surface.

Main 
code

Sub 

code

Title

Half-tone process control 1st 
batch trouble (Black)

F2

80

Display

Lamp/Message

Phenomenon Detail

First step operation error 
during half-tone process 
control

Section

—

Common

Check

Use SIM 44-2 to adjust the 
process control sensor 
gain.

Case 1

Cause

When "Error" occurs in the 
gain adjustment of SIM 44-
2:
1. Disconnection of the 

harness between the 
PCU PWB and the 
image density sensor.

2. Image density sensor 

dirt/trouble

Check & 
Remedy

1. Check connection of the 

harness between the 
PCU PWB and the 
image density sensor.

2. Clean/replace the 

image density sensor.

Case 2

Cause

When SIM 44-2 gain 
adjustment is completed:
Insufficient cleaning of the 
transfer belt, calibration 
plate solenoid operation 
trouble

Check & 
Remedy

Check the drum surface 
and the belt surface.

Summary of Contents for AR-BC320

























































































































































































































































































































































Reviews:

No comments