manualshive.com logo in svg

Sharp AR-BC320, Service Manual, Page: 198 / 344

Share
Download
Sharp AR-BC320 Service Manual Download Page 198

AR-BC320  SIMULATION  9 - 44

∗

This simulation is not normally used. Adjustment is made with 
SIM 40-02.

(Set range)

(Sensors to be detected)

2. Set an A3 paper (11" x 17") and press the [EXECUTE] key. 

The sensor level setting with document is performed.

3. The message of completion of the adjustment is displayed.

∗

The value in [ ] shown at the right of each sensor name is the 
threshold value.

PD1 – PD7 light receiving (A/D value) and threshold value (A/D 
value) range is 1 – 255. The default of the threshold value is 128.

40

-7

Purpose

Setting

Function 
(Purpose)

Used to enter the adjustment value of the manual 
paper feed tray paper width detector detection level. 
(Setting)

Section

Paper feed

Item

Specifications

Operation/
Procedure

1. Select the item (setting) to be entered with the 

scroll key.

2. Enter the adjustment value with the 10-key pad.
3. Press the [OK] key.

Item

Set range

Default

A

MAX POSITION

0 – 255

241

B

P1 POSITION

0 – 255

231

C

P2 POSITION

0 – 255

140

D

MIN POSITION

0 – 255

19

41

41

-1

Purpose

Operation test/check

Function 
(Purpose)

Used to check the operation of the document size 
sensor and the related circuit. (The operation of the 
document size sensor can be monitored with the 
LCD display.)

Section

Others

Item

Operation

Operation/
Procedure

The active sensors and detectors are highlighted.

OCSW

OC cover open/close 

detection

Open: Highlighted,

Close: Normal

PD1

Document sensor 1

No document (not detected): 
Normal
Document loaded (detected): 
Highlighted

PD2

Document sensor 2

PD3

Document sensor 3

PD4

Document sensor 4

PD5

Document sensor 5

PD6

Document sensor 6

PD7

Document sensor 7

41

-2

Purpose

Adjustment

Function 
(Purpose)

Used to adjust the document size sensor detection 
level.

Section

Others

Item

Operation

Operation/
Procedure

1. Open the document table, and press the 

[EXECUTE] key without document on the 
document table. The sensor level setting with no 
document on the table is performed.

41

-3

Purpose

Operation test/check

Function 
(Purpose)

Used to check the operation of the document size 
sensor and the related circuit. (The document size 
sensor output level can be monitored with the LCD 
display.)

Section

Others

Item

Operation

Operation/
Procedure

The detection output level of each sensor (PD1 – 
PD7) is displayed in real time.

43

43

-1

Purpose

Setting

Function 
(Purpose)

Used to set the fusing temperature in each 
operation mode.

Section

Fixing (Fusing)

Item

Operation

Operation/
Procedure

1. Select the kind of lamps and the operation mode 

with the scroll key.

Summary of Contents for AR-BC320

























































































































































































































































































































































Reviews:

No comments