manualshive.com logo in svg

Sharp AR-BC320, Service Manual, Page: 277 / 344

Share
Download
Sharp AR-BC320 Service Manual Download Page 277

AR-BC320  ROM VERSION UP  12 - 4

(2)

Method of copying with two Flash ROM sockets on the ICU MAIN PWB
The program for each PWB in the Flash ROM (Source ROM) on the Read side Flash ROM socket is copied to a Flash ROM on the
Write side socket.

*1: This Flash ROM was made by writing the program data from PC to the ICU MAIN PWB Flash ROM.

NOTE: Besides this method of Flash ROM version up, there is another method by use of a machine of the AR-350/450 series.

This method, however, allows the version up work in a shorter time.
For details, refer to Technical Report ARE-352 (ARJ-390).

(Desk control ROM)

The desk unit control program is installed in the Flash ROM in the
CPU of the desk unit control PWB.

Therefore, this Flash ROM cannot be replaced physically.

The PC is connected with the desk unit control PWB, and the
Flash Rom program is written from the PC to the Flash Rom in the
CPU.

2. Precautions

A. Relationship between each ROM and version 

up

When making version up of ROM, check the combination with the
version of ROM installed to the other PWB including options.

In some combination of ROM versions, the machine may not oper-
ate normally.

If all the ROM's are of the latest versions, there is no problem.

Read side Flash ROM (ROM B) (*1)

Write side Flash ROM (Flash ROM C)

Note

Capacity

Content

Name

Capacity

Copied content

32Mbit x 2

Program for 
PCU Flash 
ROM

Program for 
Flash ROM 
Copy (ROM 
to ROM)

For PCU 
Flash ROM

8Mbit

Program for 
PCU Flash 
ROM

The Flash ROM on the Read side is the 
source ROM for PCU, which was made 
by writing the program data from PC to 
the Flash ROM.

32Mbit x 2

Program for 
ICU Flash 
ROM

Program for 
Flash ROM 
copy (ROM 
to ROM)

For ICU 
Flash ROM

32Mbit x 2

Program for 
ICU Flash 
ROM

The Flash ROM on the Read side is the 
source ROM for ICU, which was made 
by writing the program data from PC to 
the Flash ROM.

32Mbit x 2

Program for 
operation 
control 
Flash ROM

Program for 
Flash ROM 
copy (ROM 
to ROM)

For 
operation 
control 
Flash ROM

16Mbit x 2

Program for 
operation 
control 
Flash ROM

The Flash ROM on the Read side is the 
source ROM for operation control PWB, 
which was made by writing the program 
data from PC to the Flash ROM.

32Mbit x 2

Program for 
scanner 
control 
Flash ROM

Program for 
Flash ROM 
copy (ROM 
to ROM)

Program 
for scanner 
control 
Flash ROM

16Mbit x 2

Program for 
scanner 
control 
Flash ROM

32Mbit x 2

Program for 
FAX control 
Flash ROM

Program 
for FAX 
control 
Flash ROM

8Mbit x 2

Program for 
FAX control 
Flash ROM

PC side

Write side (Flash ROM 

in the CPU on the Desk 

unit control PWB)

Content

File name

Copied content

Program for 
Desk control 
PWB Flash ROM

WDskxxx_d.pgm

Program for Desk 
control PWB Flash 
ROM

Summary of Contents for AR-BC320

























































































































































































































































































































































Reviews:

No comments