manualshive.com logo in svg

Sharp AR-BC320, Service Manual, Page: 129 / 344

Share
Download
Sharp AR-BC320 Service Manual Download Page 129

AR-BC320  SETTING AND ADJUSTMENTS  8 - 22

(1) Note for the copy color balance/density adjustment

(Necessary conditions for execution of the copy color balance/density adjustment)

Before execution of the copy color balance/density adjustment, check that all the adjustments related to the copy color balance and density
have been completed properly.

The importance level is as shown below.

(Adjustment items which directly affect the copy color balance and density and must be checked or adjusted 
before execution of the image quality adjustment)

1) Adjustment items: ADJ 2, ADJ 3, ADJ 4

The user color balance adjustment must be set to the center (default).

The set value of SIM 46-27 is set to the default.

The set value of the following simulation must be set to the default.

Adjustment item

Adjustment 

value

Note

IMAGE 
LOSS

Lead edge image 
loss

4.0 ± 

1.0mm

The greater the set value is, 
the greater the image loss is.

DEN-A

Lead edge void 
area

4.0 ± 

1.0mm

The greater the set value is, 
the greater the void area is.

DEN-B

Rear edge void 
area

4.0 ± 

1.0mm

The greater the set value is, 
the greater the void area is.

ADJ 11

Copy color balance/density adjustment

JOB No

ADJUSTMENT ITEM LIST

SIMULATION

ADJ 2

Image density sensor adjustment

44-2/44-13

ADJ 3

Image focus, image skew adjustment (LED (writing) unit)

64-1/61-4

ADJ 4

Image registration adjustment

ADJ 4A

Image registration adjustment (Auto adjustment)

50-22

ADJ 4B

Image registration adjustment (Manual adjustment)

50-20

Item

Purpose

Note

User color balance setting: Default (Center) (Special function) Set the color balance to the standard state. Check that it is set to the center.

SIM 

No

Display/Item

Setting 

(Default)

Content

Phenomenon when the set value 

is changed

Phenomenon occurring 

when the adjustment 

value is not within the 

normal value range.

Note

46-27 A BLACK TEXT

(SLOPE)

50

Black image edge section 
gamma (tilt) adjustment 
(Black text and black line 
reproduction adjustment)

When the set value is increased, 
the contrast of black line and black 
text outline sections is reduced. 
On the contrary, when the set 
value is decreased, the contrast is 
increased. (Sharpness of black 
text and black lines is changed.) 
(Text/Printed photo, Text, Text/
Photograph copy mode)

The contrast and density 
of lines and text outline 
section are changed. 
(Sharpness of text and 
lines is changed.) (Text/
Printed photo, Text, Text/
Photograph copy mode)

For image 
quality 
adjustment, 
set to 50.

B BLACK  TEXT

(INTERCEPT)

50

Black image edge section 
density (overall level) 
adjustment (Black txt and 
black line reproduction 
adjustment)

The density of black lines and 
black text outline is changed. 
(Text/Printed photo, Text, Text/
Photograph copy mode)

SIMNo

Item

Setting 

(Default)

Phenomenon when the set value is changed

Note

46-1

A –  R

50

The density and color balance in the low density 
section of color copy are changed.

Set to the default when adjusting the copy quality.
Do not adjust the density in the low density section by 
using this simulation.

46-2

A –  K

50

The density in the low density section of 
monochrome copy is changed.

46-10 to 16

A – O

500

The color copy density and color balance are 
changed. (each copy mode)

Set to the default when adjusting the copy quality.

46-20

A – O

500

The color copy density and color balance of all 
copy modes are changed.

Set to the default when adjusting the copy quality.

Summary of Contents for AR-BC320

























































































































































































































































































































































Reviews:

No comments