manualshive.com logo in svg

Sharp AR-BC320, Service Manual, Page: 264 / 344

Share
Download
Sharp AR-BC320 Service Manual Download Page 264

AR-BC320  TROUBLESHOOTING  11 - 17

F2

90

Case 2

Cause

When SIM 44-2 gain 
adjustment is completed: 
Insufficient cleaning of the 
transfer belt, calibration 
plate solenoid operation 
trouble

Check & 
Remedy

Check the drum surface 
and the belt surface.

Main 
code

Sub 

code

Title

Cassette 1 lift-up trouble

F3

12

Display

Lamp/Message

Phenomenon Detail

LUD1 does not turn on 
within the specified time.

Section

—

Case 1

Cause

LUD1 sensor trouble, 
disconnection of harness 
among the PCU PWB, the 
lift-up unit, and the paper 
feed unit.

Check & 
Remedy

Check LUD1, its harness, 
and the connector.

Case 2

Cause

Cassette 1 lift-up motor 
trouble

Check & 
Remedy

Check the lift-up unit.

Main 
code

Sub 

code

Title

ICU-FAX communication trouble 
(ICU detection)

F6

00

Display

Lamp/Message

Phenomenon Detail

Communication 
establishment error, 
framing, parity, protocol 
error

Section

FAX

Case 1

Cause

Slave unit PWB connector 
connection trouble. Slave 
unit PWB-ICU PWB 
harness trouble

Check & 
Remedy

Check connection between 
the slave unit PWB and the 
ICU PWB, and check the 
harness.

Case 2

Cause

Broken pin of the mother 
board connector of the 
slave unit PWB

Check & 
Remedy

Check the connector of the 
slave unit PWB.

Case 3

Cause

Slave unit ROM trouble/ 
No ROM/ Improper 
insertion of ROM/ ROM pin 
breakage

Check & 
Remedy

Check grounding of the 
main unit. Check the ROM 
of the slave unit PWB.

Main 
code

Sub 

code

Title

Half-tone process limit error

Main 
code

Sub 

code

Title

FAX expansion flash memory 
abnormality (ICU detection)

F6

01

Display

Lamp/Message

Phenomenon Detail

An expansion flash 
memory with SRAM 
backup data in it is 
installed.

Section

FAX

Case 1

Cause

SRAM backup data are 
detected in the expansion 
flash memory. The 
simulation function (SIM 
66-19) is provided to save 
SRAM backup data into an 
expansion flash memory. 
This trouble occurs when 
an expansion flash 
memory to which SRAM 
backup data are saved 
with the above function is 
installed.

Check & 
Remedy

Use SIM 66-20 to restore 
the backup data to the 
SRAM, and use SIM 66-10 
to clear the expansion 
flash memory. If the data 
are unnecessary, simply 
clear the expansion 
memory with SIM 66-10.

Main 
code

Sub 

code

Title

FAX MODEM operation 
abnormality

F6

04

Display

Lamp/Message

Phenomenon Detail

FAX PWB MODEM chip 
operation trouble

Section

FAX

Case 1

Cause

Normal operation is made 
with the FAX PWB SW101 
on the BOOT side. FAX 
PWB MODEM chip 
operation trouble

Check & 
Remedy

Set the FAX PWB SW101 
to the other side than the 
BOOT side, and supply 
power again. Replace the 
FAX PWB.

Main 
code

Sub 

code

Title

FAX write protect release

F6

20

Display

Lamp/Message

Phenomenon Detail

The write protect JP of the 
ICU PWB is released.

Section

FAX

Case 1

Cause

The FAX write protect pin 
is set to Write Enable.

Check & 
Remedy

Check the write protect pin 
of the ICU PWB.

Case 2

Cause

ICU PWB trouble

Check & 
Remedy

Replace the ICU PWB.

Case 3

Cause

FAX PWB trouble

Check & 
Remedy

Replace the FAX PWB.

Summary of Contents for AR-BC320

























































































































































































































































































































































Reviews:

No comments