manualshive.com logo in svg

Sharp AR-BC320, Service Manual, Page: 54 / 344

Share
Download
Sharp AR-BC320 Service Manual Download Page 54

AR-BC320  DESCRIPTIONS OF EACH SECTION  7 - 13

4) Fold the transfer belt housing and remove the transfer belt.

Note for installation:

When installing the transfer belt, be sure to place the lot number
section marked inside the transfer belt on the front side.

g. Transfer roller

1) Remove the transfer unit from the machine.

2) Remove the connector and the screw, and remove the belt

drive unit.

3) Remove the transfer belt.

4) Disengage the pawl, and remove the bearing and the transfer

roller.

Note for assembly:

There are two different transfer roller bearings: black and white.
The black bearing is conductive, and must be attached to the elec-
trode side (rear frame side).

h. Transfer drive roller

1) Remove the transfer unit from the machine.

2) Remove the connector and the screw, and remove the belt

drive unit.

3) Remove the transfer belt.

4) Remove the E-ring and the bearing, and remove the transfer

drive roller.

i. Transfer follower roller

1) Remove the transfer unit from the machine.

2) Remove the connector and the screw, and remove the belt

drive unit.

3) Remove the transfer belt.

4) Remove the E-ring and the bearing, and remove the transfer

follower roller.

j. Transfer cleaning blade

1) Remove the transfer unit from the machine.

2) Remove the connector and the screw, and remove the belt

drive unit.

3) Remove the waste toner tank unit.

4) Remove the screw, and remove the transfer cleaning blade.

k. Transfer belt cleaning roller

1) Remove the transfer unit from the machine.

2) Remove the connector and the screw, and remove the belt

drive unit.

3) Remove the waste toner tank unit.

4) Press the cleaning lever in the arrow direction A, extend the

pawl in the arrow direction B, and pull up the cleaning level in
the arrow direction C.

5) Remove the transfer belt cleaning roller.

Lot number marking

Front

Rear

Conductive

A

B

C

Summary of Contents for AR-BC320

























































































































































































































































































































































Reviews:

No comments