manualshive.com logo in svg

Sharp AR-BC320, Service Manual, Page: 190 / 344

Share
Download
Sharp AR-BC320 Service Manual Download Page 190

AR-BC320  SIMULATION  9 - 36

(Selection item)

*1: An original of 8.5" x 14" is detected as 8.5" x 13".

*2: An original of B4 size is detected as 8.5" x 13".

*3: An original of A4R size is detected as 8.5" x 13".

*4: An original of 8.5" x 14" is detected as 8.5" x 13".

*5: Applicable by replacing the AR-RF2 original tray.

*6: Can be set with the key operator program.

*7: Determined by the paper type of the destination.

[Copy vendor mode]

1. Select the kind of the counter with the scroll key.
2. Enter "1" or "2" with the 10-key pad and press the [OK] key.

Used unit

Destination

Set value

0 (Default) 

(Disable)

1 (Enable)

Document AR-RF2

Japan

A4R

A4R

 *5

AB series 
(SUK/SEEG)

A4R

A4R

 *5

AB series 
(SCA/Others)

A4R

8.5" x 13" 

 *3

Inch series 
(SEC/SECL)

8.5" x 14"

8.5" x 14" 

 *5

Inch series 
(Others)

8.5" x 14"

8.5" x 13" 

 *1

Document table

Japan/EX 
Japan AB 
series

B4

8.5" x 13" 

 *2

Inch series

8.5" x 14"

8.5" x 13"

 *1

Paper

Machine Manual 

paper 
feed tray

All 
destinations

8.5" x 14"

8.5" x 13" 

 *4

Paper 
feed tray

All 
destinations

–*

6

AR-LC5 (LCC) 

All 
destinations

–

Item

Set 

value

Content

LCC

1

8.5 x 11 (Default)

2

A4

Legal (Inch series) 

*7

0

8.5 x 14 (Default)

1

8.5  x  13

Legal (AB series) 

*7

0

B4 (Default)

1

8.5  x  13

26

-3

Purpose

Setting

Function 
(Purpose)

Used to set the auditor specification mode. Setting 
must be made according to the use conditions of 
the auditor.

Section

Auditor

Item

Specifications

Operation/
Procedure

Enter the code number corresponding to the auditor 
specification mode.

Mode

Content

[P10]

Built-in auditor mode

[AR-EC1]

Card counter mode (only Japan)

[MODE1]

Coin vendor mode 1

[MODE2]

Coin vendor mode 2

[MODE3]

Coin vendor mode 3

Diag 

setting

Specified 

number 

completed 

with money 

left

Lack of money during

a copy job

Specified 

number 

completed 

with no 

money left

BW/Color 

(with no 

money left)

Color (with 

money left)

Case 1

Case 2

Case 3

Case 4

26-3=3

MODE1

Operation 1

Operation 2

Operation 2

Operation 1

26-3=4

MODE2

Operation 1

Operation 1

Operation 2

Operation 1

26-3=5

MODE3

Operation 1

Operation 3

Operation 2

Operation 3

Operation 1: The set status remains until the auto clear set 

time has passed. (Default: 60sec Changeable 
with key operations.)

Operation 2:  Auto clear is not made. 

Operation 3:  Setting is immediately cleared, and the display 

returns to the standby menu. 

Case 1/Case 2 (with money left): B/W copy is allowed. If, however, 
charge money fro color copy is exhausted during a color copy job, 
when sufficient money for the job is supplied, only the color start 
key of the READY lamp lights up.

26

-5

Purpose

Setting

Function 
(Purpose)

Used to set the count mode of the total counter and 
the maintenance counter.

Item

Specifications

Counter

Operation/
Procedure

Used to set the single count-up or double count-up 
for the total counter, the maintenance counter, and 
the developer counter when printing is performed 
with A3, 11 x 17" paper.

Item

Content

Set range

Default

A

TOTAL(B/W)

Total counter (B/W)

1 –  2

2

B

TOTAL(COL)

Total counter (Color)

1 –  2

2

C

MAINTE(B/W)

Maintenance (B/W)

1 –  2

2

D

MAINTE(COL)

Maintenance (Color)

1 –  2

2

Summary of Contents for AR-BC320

























































































































































































































































































































































Reviews:

No comments