manualshive.com logo in svg

Sharp AR-BC320, Service Manual, Page: 269 / 344

Share
Download
Sharp AR-BC320 Service Manual Download Page 269

AR-BC320  TROUBLESHOOTING  11 - 22

Main 
code

Sub 

code

Title

Shift motor trouble

L4

11

Display

Lamp/Message

Phenomenon Detail

When initializing the shift 
motor, the change in the 
shift motor home position 
sensor characteristics is 
not detected within the 
specified time.

Section

Paper feed

Case 1

Cause

Shift motor trouble, 
disconnection of the 
harness between the PCU 
PWB and the shift motor, 
control circuit trouble

Check & 
Remedy

Use SIM 6-1 to check the 
shift motor operation. Use 
SIM 30-1 to check the shift 
motor home position 
sensor. Check the harness 
and the connector between 
the PCU PWB and the shift 
motor.

Main 
code

Sub 

code

Title

Full wave signal not provided

L8

01

Display

Lamp/Message

Phenomenon Detail

The full wave signal is not 
provided.

Section

—

Case 1

Cause

PCU PWB trouble

Check & 
Remedy

Replace the PCU PWB.

Case 2

Cause

Power supply unit trouble

Check & 
Remedy

Replace the power supply 
unit.

Case 3

Cause

Harness trouble

Check & 
Remedy

Check connection of the 
harness and the 
connector.

Main 
code

Sub 

code

Title

Full wave signal width 
abnormality

L8

02

Display

Lamp/Message

Phenomenon Detail

An abnormality of the full 
wave signal frequency is 
detected. (The detected 
frequency is 65kHz or 
above, or 45kHz or below.)

Section

—

Case 1

Cause

PCU PWB trouble

Check & 
Remedy

Replace the PCU PWB.

Case 2

Cause

Power supply unit trouble

Check & 
Remedy

Replace the power supply 
unit.

Case 3

Cause

Harness trouble

Check & 
Remedy

Check connection of the 
harness and the 
connector.

Main 
code

Sub 

code

Title

Main power switch abnormality 
detection

L8

04

Display

Lamp/Message

Phenomenon Detail

Though the PCU program 
is operating (the power is 
supplied), the main power 
switch OFF is detected.

Section

—

Case 1

Cause

Main power switch trouble

Check & 
Remedy

Replace the main power 
switch.

Case 2

Cause

Power supply unit trouble

Check & 
Remedy

Replace the power supply 
unit.

Case 3

Cause

Harness trouble

Check & 
Remedy

Check connection of the 
harness and the 
connector.

Main 
code

Sub 

code

Title

RIC copy inhibit signal reception

PF

00

Display

Lamp/Message

Phenomenon Detail

The copy inhibit signal 
from RIC (host) is 
received.

Section

—

Case 1

Cause

Depends on a judgment by 
the host.

Check & 
Remedy

Make notification to the 
host. Use SIM 27-1 to 
ignore.

Main 
code

Sub 

code

Title

ICU-OPE communication trouble 
(ICU/OPE detection)

U0

00

Display

Lamp/Message

Phenomenon Detail

Communication 
establishment error, 
framing/parity/protocol 
error
ROM version mismatching

Section

—

Case 1

Cause

Disconnection of the 
operation panel 
communication connector 
of the ICU/MFP PWB, 
harness trouble between 
the ICU PWB and the MFP 
PWB.

Check & 
Remedy

Check the connector and 
the harness between the 
ICU PWB and the MFP 
PWB.

Case 2

Cause

ICU/MFP PWB trouble

Check & 
Remedy

Check grounding of the 
machine.
Replace the ICU PWB or 
the MFP PWB.

Case 3

Cause

When the OPE-ROM 
without security functions 
is installed for the ICU-
ROM with security kit 
functions.

Check & 
Remedy

Check the ROM version, 
and replace it if necessary.

Summary of Contents for AR-BC320

























































































































































































































































































































































Reviews:

No comments