Sharp AR-BC320 Service Manual Download Page 236

Page: 236 / 344

AR-BC320 MAINTENANCE LIST 10 - 1

[10] MAINTENANCE LIST

1. Maintenance system table

: Check (Clean, replace, or adjust as necessary.)

❍

: Clean

▲

: Replace

∆

: Adjust

✩

: Lubricate

❏

: Shift position

Unit Name

No.

Part name

When

calling

50K

100K 150K 200K 250K 300K 350K 400K

Remark

Drum peripheral
section

Drum (B/W, Color)

▲

Charging unit

▲

Cleaner blade

▲

Toner reception seal

▲

Drum cartridge

▲

When replacing the
unit

Developing section
(integrated with
toner cartridge)

Toner cartridge

Replaced by user when toner empty

(or at the specified distance covered)

Transfer section

Transfer belt

▲

Replace at 100K or
within 2 years.

Transfer roller

▲

Transfer belt cleaning
blade

▲

Replace at 100K or
within 2 years.

Transfer discharge
sheet

❍

Transfer belt cleaning
roller

▲

Transfer drive roller

Transfer follower roller

Transfer cleaning brush

Sensors

10 Waste toner tank unit

▲

When waste toner full
is detected.

11 Transfer belt unit

▲

Replace the unit at
100K or within 2 years.

Fusing section

Upper heat roller

▲

Replace at 100K or
within 2 years.

Lower heat roller

▲

Replace at 100K or
within 2 years.

Heat roller gear

▲

100K

Heat roller bearing

▲

100K

Separation pawl

▲

100K

Thermistor

▲

100K

Bearings

Gears

✩

Paper guides

❍

10 Paper exit roller

11 Paper exit roller

12 Discharge brush

13 Fusing unit

▲

Replace the unit at
100K or within 2 years.

Optical section

CCD, mirror, lens,
reflector

❍

Table glass, sensors,
OC

❍

Shading glass

❍

Rails

✩

Drive wire, pulley,
pulley belt

Summary of Contents for AR-BC320

























































































































































































































































































































































Search results

Summary of Contents for AR-BC320

Reviews:

Sharp AR-BC320, Service Manual, Page: 236 / 344

Search results

Summary of Contents for AR-BC320

Reviews: