Sharp AR-BC320 Service Manual Download Page 184

Page: 184 / 344

AR-BC320 SIMULATION 9 - 30

(Sections to be displayed)

∗

The serial No. is entered in the title.
If the serial No. is invalid, "

∗∗∗∗∗∗∗∗

" is displayed.

Developing unit improper cartridge detection
(Magenta)

Developing unit improper cartridge detection (Yellow)

Developing unit CRUM trouble (Black)

Developing unit CRUM trouble (Cyan)

Developing unit CRUM trouble (Magenta)

Developing unit CRUM trouble (Yellow)

Trouble of image density sensor for registration
(Transfer belt surface reflection ratio abnormality)

Half-tone process control 1st batch error (Black)

Half-tone process control 1st batch error (Cyan)

Half-tone process control 1st batch error (Magenta)

Half-tone process control 1st batch error (Yellow)

Half-tone process control 2nd batch error (Black)

Half-tone process control 2nd batch error (Cyan)

Half-tone process control 2nd batch error (Magenta)

Half-tone process control 2nd batch error (Yellow)

Half-tone process control limit error

Cassette 1 lift up trouble

ICU-FAX communication trouble (ICU detection)

FAX expansion flash memory abnormality (ICU
detection)

FAX MODEM operation abnormality

FAX write protect release

Improper combination of the TEL/LIU PWB and the
FAX soft switch.

The FAX-BOX PWB is not one for the AR-BC320.
(FAX detection)

Improper combination of the FAX-BOX destination
data and the main unit destination data

ICU-PRT communication trouble (ICU detection)

PRT DRAM trouble

NIC port check error

HDD trouble (PRT controller detection)

Thermistor open (HL1)

Thermistor open (HL2)

Fusing section high temperature trouble (HL1)

Fusing section high temperature trouble (HL2)

Fusing section low temperature trouble (HL1)

Fusing section low temperature trouble (HL2)

Five continuous detections of POD1 not-reached
jam

Mirror feed trouble

Mirror return trouble

Paper feed motor lock trouble

Transfer belt lift motor trouble

Transfer belt motor trouble

Shift motor trouble

Full wave signal not provided

Full wave signal width abnormality

Main power switch abnormality detection

RIC copy inhibit signal reception

ICU-OPE communication trouble (ICU/OPE
detection)

RTC read trouble

EEPROM read/write error (ICU detection)

EEPROM check sum error (ICU detection)

Production No. data discrepancy (ICU

⇔

ICU)

EEPROM read/write error (SCN detection)

EEPROM check sum error (SCN detection)

EEPROM read/write error (PCU detection)

EEPROM check sum error (PCU detection)

Main
code

Sub

code

Content

ADU alignment plate operation abnormality

ADF communication trouble

ADF resist sensor defect

ADF repulsion sensor defect

ADF timing sensor defect

Paper feed motor operation abnormality

Desk communication trouble

Desk tray 1 lift motor trouble

Desk tray 2 lift motor trouble

Desk tray 3 lift motor trouble

Desk transport motor trouble

RIC communication trouble

CPT-ASIC trouble (MFP PWB trouble)

-5

Purpose

Others

Function
(Purpose)

Used to check the ROM version of each unit
(section).

Item

Software

Operation/
Procedure

If there is any problem in the software, check the
ROM version of each section with this simulation
and replace with a new version if necessary.

ICU

ICU control

PCU

Engine control section

SCN

Scanner control section

COL REV DATA

Color correction ROM

OPE PROG

OPE control section

PRT BOOT

PRT boot

PRT PROG

PRT control section

FAX

FAX control section

FIN-SORTER

Finisher/Sorter

PUNCH

Punch unit

DSK

Desk

LCC

Large capacity cassette

ADF

Automatic document feeder

NIC

PostScript

Main
code

Sub

code

Content

Summary of Contents for AR-BC320

























































































































































































































































































































































Search results

Summary of Contents for AR-BC320

Reviews:

Sharp AR-BC320, Service Manual, Page: 184 / 344

Search results

Summary of Contents for AR-BC320

Reviews: