AR-BC320 MAINTENANCE LIST 10 - 10
First digit of code: Kind of maintenance (T= Total, C= Color, A= Both)
Second digit of code: Maintenance cycle (A= 5K, B= 10K, C= 15K, D= 40K, E= 50K, F= 100K)
• Maintenance message is not displayed during a job (during operation/during job). (Message is displayed before/after a job.)
• When the maintenance counter (Total) exceeds the set value of SIM 21-1, the message is displayed.
→
The first digit of code is T.
• When the maintenance counter (Color) exceeds the set value of SIM 21-1, the message is displayed.
→
The first digit of code is C.
• When both of the maintenance counter (Total) and the maintenance counter (Color) exceed the set value of SIM 21-1, the message is
displayed.
→
The first digit of code is A.
• When SIM 26-38 is set to Print Allow, any job can be executed even during message display.
• When SIM 26-38 is set to Print Inhibit, if the specified value is exceeded by 10%, the paper feed in the machine is discharged and the
machine is stopped.
→
Same as stop by paper empty. (Paper may be left in an option unit (an after-process unit, a desk, etc.). Service-
men should take a great care for that!)
When SIM 24-4 (Maintenance counter (Total, Color) clear) is executed after completion of maintenance, the message is cleared.
B. Relationship of transfer unit system counter, display message, and machine operations
In addition to the above counters, the transfer waste-toner full sensor status is taken into consideration to make a message.
Code: TK (Transfer Kit)
• The count-up timing and the count number of are synchronous between the transfer unit print counter and the maintenance counter.
• The transfer unit accumulated mileage is the product of the transfer unit drive speed (140 or 117 or 58.5mm/s) and the transfer unit drive
time (measured by every second).
• The use days of the transfer unit is the days of passage after execution of SIM 24-4 (Transfer unit counter clear).
• Execute SIM 24-4 (Transfer unit counter clear) to clear the transfer unit print counter, the transfer unit accumulated mileage, the copy
quantity counter after detection of near end by the sensor, and the use days of the transfer unit, and the message is cleared.
• If there is any job being executed when the transfer unit life end is detected, the paper feed in the machine is discharged and the machine
is stopped.
→
Same as stop by paper empty. (Paper may be left in an option unit (an after-process unit, a desk, etc.). Servicemen should
take a great care for that.)
Message No.
Message
Print job YES/NO
1
(Now is maintenance timing. Code: Tx)
YES
2
(Now is maintenance timing. Code: Cx)
YES
3
(Now is maintenance timing. Code: Ax)
YES
4
Now is maintenance timing. Code: Tx
NO
5
Now is maintenance timing. Code: Cx
NO
6
Now is maintenance timing. Code: Ax
NO
Counter name
Near end value
Message when near end is over
When SIM 26-38 is
set to Print Allow.
When SIM 26-38 is
set to Print Inhibit.
Transfer unit print counter
49,000 [sheet]
Message 1
Message 1
Accumulated mileage of transfer unit
20,890,333 [mm]
—
—
Number of use days of transfer unit
725 [day]
—
—
Counter name
End value
Message when end is over
When SIM 26-38 is
set to Print Allow.
When SIM 26-38 is
set to Print Inhibit.
Transfer unit print counter
50,000[sheet]
Message 1
Message 3
Accumulated mileage of transfer unit
21,316,667 [mm]
—
—
Number of use days of transfer unit
740 [day]
—
—
Sensor name
Near end value
Message when near end is detected
When SIM 26-38 is
set to Print Allow.
When SIM 26-38 is
set to Print Inhibit.
Transfer waste-toner full sensor
3 sec continuously
ON
—
Message 1
Sensor name
End value
Message when end is detected
When SIM 26-38 is
set to Print Allow.
When SIM 26-38 is
set to Print Inhibit.
Transfer waste-toner full sensor
1000 [sheet] after
detection of near end
Message 1
Message 3
Message No.
Message
Print job YES/NO
1
(Now is maintenance timing. Code: TK)
YES
3
Now is maintenance timing. Code: TK
NO
Summary of Contents for AR-BC320
Page 340: ...Memo ...
Page 341: ...Memo ...