manualshive.com logo in svg

Sharp AR-BC320, Service Manual, Page: 252 / 344

Share
Download
Sharp AR-BC320 Service Manual Download Page 252

AR-BC320  TROUBLESHOOTING  11 - 5

Main 
code

Sub 

code

Title

LED controller output trouble 
(Black)

E7

24

Display

Lamp/Message

Phenomenon Detail

When printing, the print 
end signal for each page is 
not properly provided.

Section

LED/ICU PWB

Case 1

Cause

Disconnection of the LED 
head connector.

Check & 
Remedy

Check connection of the 
LED head connector.

Case 2

Cause

Disconnection of the 
harness inside the LED 
head.

Check & 
Remedy

Replace the LED head 
unit.

Case 3

Cause

ICU PWB abnormality

Check & 
Remedy

Replace the ICU PWB.

Main 
code

Sub 

code

Title

LED controller output trouble 
(Cyan)

E7

25

Display

Lamp/Message

Phenomenon Detail

When printing, the print 
end signal for each page is 
not properly provided.

Section

LED/ICU PWB

Case 1

Cause

Disconnection of the LED 
head connector.

Check & 
Remedy

Check connection of the 
LED head connector.

Case 2

Cause

Disconnection of the 
harness inside the LED 
head.

Check & 
Remedy

Replace the LED head 
unit.

Case 3

Cause

ICU PWB abnormality

Check & 
Remedy

Replace the ICU PWB.

Main 
code

Sub 

code

Title

LED controller output trouble 
(Magenta)

E7

26

Display

Lamp/Message

Phenomenon Detail

When printing, the print 
end signal for each page is 
not properly provided.

Section

LED/ICU PWB

Case 1

Cause

Disconnection of the LED 
head connector.

Check & 
Remedy

Check connection of the 
LED head connector.

Case 2

Cause

Disconnection of the 
harness inside the LED 
head.

Check & 
Remedy

Replace the LED head 
unit.

Case 3

Cause

ICU PWB abnormality

Check & 
Remedy

Replace the ICU PWB.

Main 
code

Sub 

code

Title

LED controller output trouble 
(Yellow)

E7

27

Display

Lamp/Message

Phenomenon Detail

When printing, the print 
end signal for each page is 
not properly provided.

Section

LED/ICU PWB

Case 1

Cause

Disconnection of the LED 
head connector

Check & 
Remedy

Check connection of the 
LED head connector.

Case 2

Cause

Disconnection of the 
harness inside the LED 
head.

Check & 
Remedy

Replace the LED head unit

Case 3

Cause

ICU PWB abnormality

Check & 
Remedy

Replace the ICU PWB.

Main 
code

Sub 

code

Title

LED control ASIC connection 
abnormality

E7

28

Display

Lamp/Message

Phenomenon Detail

Access error between the 
PCU PWB CPU and the 
LED control ASIC

Section

ICU/PCU PWB

Case 1

Cause

Disconnection of the ICU/
PCU PWB communication 
connector

Check & 
Remedy

Check connection of the 
ICU/PCU PWB 
communication connector

Case 2

Cause

ICU/PCU PWB 
communication harness 
trouble.

Check & 
Remedy

Check the ICU/PCU PWB 
communication harness.

Case 3

Cause

ICU PWB/PCU PWB 
trouble

Check & 
Remedy

Check grounding of the 
machine. Replace the ICU 
PWB or the PCU PWB.

Main 
code

Sub 

code

Title

ICU PWB matching error

E7

30

Display

Lamp/Message

Phenomenon Detail

Check matching between 
the machine and the ICU 
PWB (by the identification 
port) when the power is 
turned on. If matching is 
improper, it is judged as a 
trouble.

Section

ICU PWB

Case 1

Cause

An ICU PWB for the AR-
C260/C260M is installed to 
the AR-BC320.

Check & 
Remedy

Replace the ICU PWB.

Case 2

Cause

ICU PWB abnormality 
(When the identification 
port is abnormal)

Check & 
Remedy

Replace the ICU PWB.

Summary of Contents for AR-BC320

























































































































































































































































































































































Reviews:

No comments