Sharp AR-BC320, Service Manual, Page: 173 / 344

AR-BC320 SIMULATION 9 - 19
2. Press the [EXECUTE] key. The selected load operates.
During the load operation, the [EXECUTE] key and the load key
are highlighted. Under this state, pressing the [EXECUTE] key
interrupts the load operation.
(Loads to be selected)
(When the finisher is installed)
(Sensors to be detected)
3 -3
Purpose Operation test/check
Function
(Purpose) Used to check the loads in the finisher and the
control circuit.
Section Finisher
Item Operation
Operation/
Procedure 1. The names of the loads that can be checked are
displayed. Select a load to be checked with the
key.
FFM Transport motor FFSM Stapler motor
FPM Paddle motor FLM Shift motor
FAM Bundle exit motor FPNM Punch motor
FFJM Alignment motor (F) FPSM Puncher side resist motor
FRJM Alignment motor (R) FFC Folding clutch
FSM Slide motor
SBSM Bin unit shift motor
SPFM Transport motor
SGBM Guide bar drive motor
3 -10
Purpose Operation test/check
Function
(Purpose) Used to adjust the sections in the finisher.
Section Finisher
Item Operation
Operation/
Procedure 1. Select the adjustment item with the scroll key.
2. Enter the adjustment value with the 1o-key and
press the OK key to set the value.
Item
Set
range
Initial
value
A Saddle binding position adjustment 0 – 400 200
B Saddle folding position adjustment 0 – 400 200
C Front alignment position adjustment 0 – 20 10
D Rear alignment position adjustment 0 – 20 10
E Staple rear one-point binding position
adjustment 0 – 200 100
F Staple front one-point binding position
adjustment 0 – 200 100
G Staple two-point binding center adjustment 0 – 200 100
H Staple two-point binding pitch adjustment 0 – 100 50
I Punch center adjustment 47 – 53 50
J Punch hole position adjustment 0 – 100 50
4
4 -2
Purpose Operation test/check
Function
(Purpose) Used to check the operations of the desk/large
capacity tray sensors and detectors and the related
circuits.
Section Paper feed
Item Operation
Operation/
Procedure The operating conditions of the sensors and
detectors in the paper feed section are displayed.
The active sensors and detectors are highlighted.
DLUD1 Desk 1cs upper limit detection
DLUD2 Desk 2cs upper limit detection
DLUD3 Desk 3cs upper limit detection
DPED1 Desk 1cs paper empty detector
DPED2 Desk 2cs paper empty detection
DPED3 Desk 3cs paper empty detection
DCSPS1 Desk 1cs remaining quantity detection
DCSPS2 Desk 2cs remaining quantity detection
DCSPS3 Desk 3cs remaining quantity detection
DPPD1 Desk paper transport detection 1
DPPD2 Desk paper transport detection 2
DPPD3 Desk paper transport detection 3
DLUID1 Desk 1cs lift unit installation detection
DLUID2 Desk 2cs lift unit installation detection
DLUID3 Desk 3cs lift unit installation detection
DDOPD Desk door open detection
DCSS11 Desk 1cs paper size detection 1
DCSS12 Desk 1cs paper size detection 2
DCSS13 Desk 1cs paper size detection 3
DCSS14 Desk 1cs paper size detection 4
DCSS21 Desk 2cs paper size detection 1
DCSS22 Desk 2cs paper size detection 2
DCSS23 Desk 2cs paper size detection 3
DCSS24 Desk 2cs paper size detection 4
DCSS31 Desk 3cs paper size detection 1
DCSS32 Desk 3cs paper size detection 2
DCSS33 Desk 3cs paper size detection 3
DCSS34 Desk 3cs paper size detection 4
LRE LCC remaining quantity detection
LUD LCC upper limit detection
LDD LCC lower limit detection
LPED LCC paper empty detection
LPFD LCC paper exit detection
LDSW LCC door open detection
LTOD LCC release detection
24V LCC 24V detection
LCD LCC cassette detection