manualshive.com logo in svg

Sharp AR-BC320, Service Manual, Page: 321 / 344

Share
Download
Sharp AR-BC320 Service Manual Download Page 321

AR-BC320  PRINTER CONTROLLER SECTION  14 - 9

5. Setting

A. Key operator program

(1) Printer settings

a. Default settings

These programs are used to adjust the settings of various printer
functions.

1) Prohibit notice page printing

This program is used to disable notice page printing.

Turn on this program when you do not want the machine to print
the notice page explained.

2) Prohibit test page printing

This program is used to disable test page printing.

When the program is turned on, the PRINTER TEST PAGE in the
user settings cannot be printed.

3) A4/letter size auto change

If this program is set, and printing onto A4 size paper is selected
but not available, the printer will automatically substitute 8-1/2" x
11" size paper in place of A4 paper if 8-1/2" x 11" paper is avail-
able.

∗

A4 paper cannot be automatically selected in place of 8-1/2" x
11".

NOTE: When A4 size is specified for a document attached to an

E-mail that has been transmitted from a foreign country
and 8-1/2" x 11" size paper is not installed in the printer,
printing cannot be done without operator intervention. If
this program is set, printing will be executed without inter-
vention if a paper tray is loaded with 8-1/2" x 11" paper.

4) Delete the print hold data

Use this program to manually delete all stored data from the hard
disk.

When you touch this key, a message will appear to confirm that
you want to delete the data. Check the message and then proceed
with the deletion. If you are using the job retention function, exer-
cise caution when using this program.

5) Output method when memory is full

When the internal memory becomes full with printer data, further
printing is not possible, thus the print data stored to that point is
printed. This program is used to set the condition for printing. The
factory default setting is "1 SET".

General settings/copy settings       KEY OPERATOR'S GUIDE
Network scanner settings          OPERATION MANUAL (for network scanner)

DEFAULT SETTINGS

NETWORK SETTINGS

COLOR ADJUSTMENTS

INTERFACE SETTINGS

PROHIBIT NOTICE PAGE PRINTING

PROHIBIT TEST PAGE PRINTING

A4/LETTER SIZE AUTO CHANGE

DELETE THE PRINT HOLD DATA

OUTPUT METHOD WHEN MEMORY IS FULL

DEFAULT PAPER TYPE FOR BYPASS TRAY

JOB QUEUING

PORT SWITCHING METHOD

ENABLE PARALLEL PORT

ENABLE USB PORT

ENABLE NETWORK PORT

I/O TIMEOUT

IP ADDRESS SETTING

ENABLE TCP/IP

ENABLE NetWare

ENABLE NetBEUI

RESET THE NIC

AUTO COLOR CALIBRATION

RESTORE FACTORY DEFAULTS

STORE CURRENT CONFIGURATION

RESTORE CONFIGURATION

PRINTER SETTINGS

INITIALIZE AND/OR STORE SETTINGS

Level 2

Level 1

Level 3

Enter K

e

y Oper

ator Code

For information on the following settings, see the indicated manuals.

Summary of Contents for AR-BC320

























































































































































































































































































































































Reviews:

No comments