manualshive.com logo in svg

Sharp AR-BC320, Service Manual, Page: 196 / 344

Share
Download
Sharp AR-BC320 Service Manual Download Page 196

AR-BC320  SIMULATION  9 - 42

*1: When set to "1:YES," the manual feed paper rind is set to 

heavy paper 1.

0: Though a communication trouble occurs between the host 

computer and the MODEM (machine side), the machine is not 
affected.

1: When a communication trouble occurs between the host 

computer and the MODEM (machine side), the self diag 
display (U7-00) is displayed.

2. Press the [SET] key. The new tag No. entered in procedure 1 

is set. It is advisable to enter the machine's serial No. for 
machine management and servicing.

Note: To perform this setting, the host computer and the machine

must be connected through MODEM.

(Sensors to be checked)

26

-80

Purpose

Setting

Function 
(Purpose)

Manual feed paper kind heavy paper rounding 
setting

Item

Specifications

Operation/
Procedure

1. Select NO or YES with the 10-key.

0: NO 
1: YES

2. Press the [OK] key.

Item

Content

Set range

Default

A

(0:NO

1:YES)

Manual feed paper kind 
heavy paper rounding 
setting *1

0 –  1

0

27

27

-1

Purpose

Operation test/check

Function 
(Purpose)

Used to set the specifications for operations in case 
of communication trouble between the host 
computer and MODEM (machine side). (When 
communication trouble occurs between the host 
computer MODEM and the machine, the self diag 
display (U7-00) is printed and setting for inhibition of 
print or not is made.)

Section

Communication (RIC/MODEM)

Item

Specifications

Operation mode (Common)

Operation/
Procedure

Enter the code number corresponding to the 
operation mode with the 10-key and press the [OK] 
key. Used to set Enable/Disable of U7-00 trouble 
detection.

Set 

value

Set content

Default

0

U7-00 trouble detection is made. (Default)

0

1

U7-00 trouble detection is not made.

27

-5

Purpose

Setting

Function 
(Purpose)

Used to enter the machine tag No. (This function 
allows to check the tag No. of the machine with the 
host computer.)

Section

Communication (RIC/MODEM)

Item

Data

User data

Operation/
Procedure

1. When entering the tag No. newly or changing 

the tag No., enter the value (max. 8 digits) with 
the 10-key. The entered number is displayed in 
the column of "NEW"

30

30

-1

Purpose

Operation test/check

Function 
(Purpose)

Used to check the operation of sensors and 
detectors in the paper feed, paper transport, paper 
exit sections and the related circuits.

Item

Operation

Operation/
Procedure

The active sensors and detectors are highlighted.

Sensor name

Content

PFD1

Paper feed detection 1 (Tray 1)

PPD1

Transport detection 1

PPD2

Transport detection 2

POD1

Paper exit detection 1

POD2

Paper exit detection 2 (Top tray paper exit)

DSWF

Front door switch

DSWR

Right door switch

DSWL

Left door switch

FUCHin

Fusing installation detection 

BELTch

Belt unit installation detection

BLUD

Belt unit upper limit detection 

BTNF

Belt waste toner full detection 

TFD

Side tray paper full detection 

HPOS

Shifter home position detection

TFD2

Top tray paper full detection

Summary of Contents for AR-BC320

























































































































































































































































































































































Reviews:

No comments