manualshive.com logo in svg

Sharp AR-BC320, Service Manual, Page: 153 / 344

Share
Download
Sharp AR-BC320 Service Manual Download Page 153

AR-BC320  SETTING AND ADJUSTMENTS  8 - 46

(3) Color balance adjustment result check

1) Enter the key operator program mode.

2) Select "Printer setting."

3) Select "Color adjustments."

4) Select the test print. 

5) The display below is shown. Select A4 or 8.5" x 11" size

paper, and press the EXECUTE key.

The test pattern for the color balance adjustment is printed. 

6) Check that each patch density on the printed test chart is at

the center of the Lower Limit and the Upper limit of the test
chart (UKOG-0305FCZZ).

Note: When A4 paper is loaded on the main cassette and the

option desk and LCC is connected, paper must be loaded in
all the trays of the desk and LCC. (If A3 paper is loaded, an
error occurs.)

1) Enter the SIM 50-28 mode.

2) Select an adjustment item according to your purpose.

3) The self print chart is outputted, and the machine is brought

into the self print chart scanning standby state.

When [PRINT] : [AUTO] is selected, each self print of pf CS1
and MFT is printed. (When [ADF] is selected, the output is
made from the selected cassette.)

4) Select [SCAN] to scan the outputted self print chart.

5) Select [FINISH] to display the result.

[DATA]: Scanned data are displayed.

6) Select [OK] and complete.

KEY OPERATOR PROGRAMS

EXECUTE

TEST PRINT

SELF PRINT IN PROGRESS

C

M

Y

Bk

Low Density

Mid Density

High Density

C

M

Y

Bk

C

M

Y

Bk

Low Density

Mid Density

High Density

ADJ 21

Collective adjustment of image 
position and magnification ratio

ALL OPTION CS: Used to the off-center adjustment (installation

adjustment) of the option tray (desk, LCC). (The
main tray and the manual feed tray are adjusted
in the production line and no further adjustment
is needed in installation.)

CS ADJ:

Used to the off-center adjustment, the lead edge
adjustment, and the rear edge adjustment.

OC ADJ:

Used to adjust the magnification ratio of the document
lead edge on the scanner size in the sub scanning
direction.

ADF ADJ: Used to adjust the magnification ratio of the document

on the ADF side and off-center.

C

M

Y

Bk

Low Density

Mid Density

High Density

C

M

Y

Bk

C

M

Y

Bk

AR-C260 Color Chart

Lower
Limit

Upper
Limit

Summary of Contents for AR-BC320

























































































































































































































































































































































Reviews:

No comments