Sharp AR-BC320 Service Manual Download Page 273

Page: 273 / 344

AR-BC320 TROUBLESHOOTING 11 - 26

Main
code

Sub

code

Title

Desk communication trouble

Display

Lamp/Message

Phenomenon Detail

Desk communication error,
communication test error
when turning on the power
or after canceling the
exclusive simulation.

Section

Desk

Case 1

Cause

Improper connection or
disconnection of the
connector and the
harness.

Check &
Remedy

Check the connector and
the harness in the
communication line.
Turn OFF/ON the power to
cancel the error.

Case 2

Cause

Desk control PWB trouble,
control PWB (PCU)
trouble, malfunction
caused by noises

Check &
Remedy

Turn OFF/ON the power to
cancel the error.

Main
code

Sub

code

Title

Desk cassette 1 lift-up trouble

Display

Lamp/Message

Phenomenon Detail

DLUD1 does not turn on
within the specified time.

Section

Desk

Case 1

Cause

DLUD1 sensor trouble,
paper feed unit harness
disconnection

Check &
Remedy

Check DLUD1 and the
harness and the
connector.

Case 2

Cause

Cassette 1 lift-up motor
trouble, desk PWB, lift-up
unit trouble

Check &
Remedy

Check the lift-up unit.

Main
code

Sub

code

Title

Desk cassette 2 lift-up trouble

Display

Lamp/Message

Phenomenon Detail

DLUD2 does not turn on
within the specified time.

Section

Desk

Case 1

Cause

DLUD2 sensor trouble,
paper feed unit harness
disconnection

Check &
Remedy

Check DLUD2 and the
harness and the
connector.

Case 2

Cause

Cassette 2 lift-up motor
trouble, desk PWB, lift-up
unit trouble

Check &
Remedy

Check the lift-up unit.

Main
code

Sub

code

Title

Desk cassette 3 lift-up trouble

Display

Lamp/Message

Phenomenon Detail

DLUD3 does not turn on
within the specified time.

Section

Desk

Case 1

Cause

DLUD3 sensor trouble,
paper feed unit harness
disconnection

Check &
Remedy

Check DLUD3 and the
harness and the
connector.

Case 2

Cause

Cassette 3 lift-up motor
trouble, desk PWB, lift-up
unit trouble

Check &
Remedy

Check the lift-up unit.

Main
code

Sub

code

Title

Desk transport motor trouble

Display

Lamp/Message

Phenomenon Detail

Desk transport motor
operation trouble

Section

—

Case 1

Cause

Motor lock, motor RPM
abnormality, Over current
to the motor, console
finisher control PWB
trouble

Check &
Remedy

Use SIM 3-3 to check the
staple motor operation.

Main
code

Sub

code

Title

RIC communication trouble

Display

Lamp/Message

Phenomenon Detail

RIC communication error,
communication test error
when turning on the power
or after canceling the
exclusive simulation.

Section

—

Case 1

Cause

Improper connection or
disconnection of the
connector and the harness

Check &
Remedy

Check the connector and
the harness in the
communication line.
Turn OFF/ON the power to
cancel the error.

Case 2

Cause

RIC control PWB trouble,
control PWB (PCU)
trouble, malfunction
caused by noises

Check &
Remedy

Turn OFF/ON the power to
cancel the error.

Main
code

Sub

code

Title

CPT-ASIC trouble (MFP PWB
trouble)

Display

Lamp/Message

Phenomenon Detail

Access abnormality to
CPT-ASIC (ASIC does not
operate normally.)

Section

MFP PWB

Case 1

Cause

CPT-ASIC abnormality
MFP PWB abnormality

Check &
Remedy

Turn OFF/ON repeatedly.
If the trouble is not
canceled, replace the MFP
PWB.

Summary of Contents for AR-BC320

























































































































































































































































































































































Search results

Summary of Contents for AR-BC320

Reviews:

Sharp AR-BC320, Service Manual, Page: 273 / 344

Search results

Summary of Contents for AR-BC320

Reviews: