manualshive.com logo in svg

Sharp AR-BC320, Service Manual, Page: 165 / 344

Share
Download
Sharp AR-BC320 Service Manual Download Page 165

AR-BC320  SIMULATION  9 - 11

46

28

Used to check pre-scanning 
operation for automatic 
recognition of document in the 
color auto copy mode. (This 
simulation is used only in 
production, and not used in the 
market.)

Adjustment

Image process (ICU) 

Picture quality Color balance

33

Used to set the foundation 
process conditions in the color 
auto copy mode, the image auto 
recognition conditions, and the 
text recognition conditions.

Setting

Image process (ICU)

Picture quality

35

Image process setting in the 
Color manual mode

Setting

Image process (ICU)

Picture quality

40

Collective adjustment of FAX 
mode (all modes) document 
scan density 
(When the FAX is installed)

Adjustment

ICU PWB / FAX

Picture quality

41

Used to adjust the FAX mode 
(normal mode) document scan 
density 
(when the FAX is installed).

Adjustment

ICU PWB / FAX

Picture quality

42

Used to adjust the FAX mode 
(fine text mode) document scan 
density 
(when the FAX is installed).

Adjustment

ICU PWB / FAX

Picture quality

43

Used to adjust the FAX mode 
(super fine mode) document 
scan density 
(when the FAX is installed).

Adjustment

ICU PWB / FAX

Picture quality

44

Used to adjust the FAX mode 
(ultra-fine mode) document scan 
density 
(when the FAX is installed).

Adjustment

ICU PWB / FAX

Picture quality

48

1

Used to adjust the copy 
magnification ratio (main 
scanning and sub scanning 
directions).

Adjustment

Picture quality Size/

magnification 
ratio

6

Used to adjust each motor RPM. Adjustment

Operation

49

1

Used for firmware version up 
(Machine/FAX).

Version up

Firmware (Machine/
FAX)

Operation

2

Used to set the data 
communication speed in version 
up of the machine firmware.

Version up

Firmware

Operation

10

Used for firmware version up 
(Desk unit).

Version up

Firmware (Desk unit)

Operation

50

1

Used to adjust the copy image 
position and the void area 
(image loss) on print paper in 
the copy mode. (The similar 
adjustment can be made also by 
SIM 50-2 (Simple method).)

Adjustment

Picture quality Image position

2

Used to adjust the copy image 
position and the void area 
(image loss) on print paper in 
the copy mode. (Simple method)
(The same content of SIM 50-1. 
However this simulation is 
easier to perform.)

Adjustment

Picture quality Image position

5

Used to adjust the image 
position and print area in the sub 
scanning direction. (Print engine 
section)

Adjustment

ICU/Printer

Picture quality

Code

Function (Purpose)

Purpose

Section

Item

Main Sub

Summary of Contents for AR-BC320

























































































































































































































































































































































Reviews:

No comments