Sharp AR-BC320 Service Manual Download Page 28

Page: 28 / 344

AR-BC320 UNPACKING AND INSTALLATION 5 - 6

5) Insert the cartridge securely until it locks.

6) Return the cartridge lever to the original position.

7) Close the front cover.

9. AC cord connection

1) Insert the AC power plug into the connector at the rear of the

machine, and connect the other end to the power outlet.

10. Machine power ON

1) Turn on the power switch on the left side of the machine.

11. Specifications setup

Used to set the specifications with SIM26 according to the cus-
tomer's request.

To customize the following items after completion of the destina-
tion setup, change the set values.

On completion of the installation of the AR-F13 finisher, please
change the default output tray of the machine to the top tray of the
finisher.

12. Image quality check

Check the following items related to image quality. For details of
the adjustment and checking procedures, refer to the chapter of
adjustments.

1) Image focus, image skew (Refer to ADJ 3.)

2) Image registration (Refer to ADJ 4.)

3) Image loss, void area (Refer to ADJ 10.)

4) Copy color balance, density (Refer to ADJ 11.)

Check that the above items are normal. If not, make the adjust-
ment.

13. Function and operation check

Check that the following operations are normal.

Do not press
this section.
(If it is pressed,
the lock lever
falls.)

SIM No

Content

Used to set the destination.

SIM No

Content

Used to set the large capacity paper feed tray paper
size.

Used to set the detection paper size and display when
using 8.5 x 13 size paper and document.

Used to set the paper kind and the display form in the
manual paper feed mode.

Used to set the auditor specification mode.

Used to set the count mode of the total counter and the
maintenance counter.

18 Used to set YES/NO of the toner save mode (Only in UK

and Japan versions) For other destination versions, this
setup is made by the user program.

52 Used to set YES/NO of counting when non-print paper is

passed through each counter.

53 Used to set YES/NO of user calibration permission.

65 Used to set the limit number of sheets for stapling.

Check item

Installation

Key input operation (Operation
panel)

Display (Operation panel)

Paper feed
operation

Manual paper
feed

Machine paper
tray

Desk unit
paper feed tray

When the desk unit is installed.

Large capacity
paper feed tray

When the large capacity paper
feed tray is installed.

Paper size detection operation

Document size
detection
operation

Document
table mode

RADF mode

When the RADF is installed.

Summary of Contents for AR-BC320

























































































































































































































































































































































Search results

Summary of Contents for AR-BC320

Reviews:

Sharp AR-BC320, Service Manual, Page: 28 / 344

Search results

Summary of Contents for AR-BC320

Reviews: