manualshive.com logo in svg

Sharp AR-BC320, Service Manual, Page: 174 / 344

Share
Download
Sharp AR-BC320 Service Manual Download Page 174

AR-BC320  SIMULATION  9 - 20

During the operation of the load, the [EXECUTE] key is 
highlighted. If the [EXECUTE] key is pressed while it is 
highlighted, the operation is stopped.

(Loads to be selected)

When the [TRC ON] key or the [TRC OFF] key is pressed, the 
TRC clutch is turned ON or OFF.

If the response of monitoring TRC ON/OFF is made, DESK 
SENSOR TRC ON/OFF is displayed.

↓

6sec

The selected heater lamp repeats ON/OFF in the frequency of 
500msec for 10sec. (The [EXECUTE] key is highlighted.) Then the 
[EXECUTE] key returns to the normal display. When the 
[EXECUTE] key is pressed during ON/OFF operation of the heater 
lamp, the heater lamp is turned OFF and the  [EXECUTE] key 
returns to the normal display.

4

-3

Purpose

Operation test/check

Function 
(Purpose)

Used to check the operations of the desk/large 
capacity tray loads and the control circuit.

/

Section

Paper feed

Item

Operation

Operation/
Procedure

1. The names of the loads that can be checked are 

displayed. Select a load to be checked with the 
key, and the selected load is highlighted.

2. Press the [EXECUTE] key. The load selected in 

procedure 1 starts the operation.

DM

Desk transport motor

DLM1

Desk 1cs lift-up motor

DLM2

Desk 2cs lift-up motor

DLM3

Desk 3cs lift-up motor

DPFC1

Desk 1cs paper feed clutch

DPFC2

Desk 2cs paper feed clutch

DPFC3

Desk 3cs paper feed clutch

DTRC

Desk transport clutch

DPFS1

Desk 1cs paper feed solenoid

DPFS2

Desk 2cs paper feed solenoid

DPFS3

Desk 3cs paper feed solenoid

LPFM

LCC transport motor

LLM

LCC lift motor up-down operation

LPFC

LCC paper feed clutch

LPFS

LCC paper feed solenoid

LLED

LCC door open LED

LTRC

LCC transport clutch

4

-5

Purpose

Operation test/check

Function 
(Purpose)

Used to check the operations of the clutch TRC and 
the monitor.

/

Section

Paper feed

Item

Operation

Operation/
Procedure

1. Press the [TRC ON] key. (The load operates.)
2. Press the [TRC OFF] key to terminate checking.

5

5

-1

Purpose

Operation test/check

Function 
(Purpose)

Used to check the operations of the display lamp 
(LED)/LCD on the operation panel and the control 
circuits.

Section

Operation (Display, procedure)

Item

Operation

Operation/
Procedure

The LCD shows the following message. 
(The contrast changes in the sequence of Current 
level 

→

 MAX 

→

 MIN 

→

 Current level 

→

 MAX 

→

 

MIN in every 2sec.) During that period, each LED is 
lighted for 12sec.

5

-2

Purpose

Operation test/check

Function 
(Purpose)

Used to check the operations of the heater lamp 
and its control circuit.

/

Section

Fusing

Item

Operation

Operation/
Procedure

1. Select the lamp to be checked with the key.
2. Press the [EXECUTE] key.

HL1 (UPPER)

Upper heater lamp

HL2 (LOWER)

Lower heater lamp

HL1&2 (UPPER & LOWER)

Upper/lower fusing heater lamp

Summary of Contents for AR-BC320

























































































































































































































































































































































Reviews:

No comments