manualshive.com logo in svg

Sharp AR-BC320, Service Manual, Page: 260 / 344

Share
Download
Sharp AR-BC320 Service Manual Download Page 260

AR-BC320  TROUBLESHOOTING  11 - 13

F2

45

Case 1

Cause

When "Error" occurs in 
SIM 44-2:
1. Dirt/defect of the image 

density sensor

2. Disconnection of the 

harness between the 
PCU PWB and the 
image density sensor

Check & 
Remedy

1. Clean/replace the 

image density sensor.

2. Connect/replace the 

harness between the 
PCU PWB and the 
image density sensor.

Case 2

Cause

When SIM 44-2 is 
completed:
1. Dirt on the calibration 

plate, calibration plate 
solenoid operation 
trouble

Check & 
Remedy

1. Clean the calibration 

plate. Replace the 
calibration plate 
solenoid.

Main 
code

Sub 

code

Title

Process humidity sensor 
breakdown

F2

58

Display

Lamp/Message

Phenomenon Detail

Process humidity sensor 
open

Section

Process

Case 1

Cause

Process humidity sensor 
harness disconnection

Check & 
Remedy

Check connection of the 
process humidity sensor 
harness.

Case 2

Cause

Process humidity sensor 
trouble

Check & 
Remedy

Replace the process 
humidity sensor.

Case 3

Cause

PCU PWB trouble

Check & 
Remedy

Replace the PCU PWB.

Main 
code

Sub 

code

Title

Developing unit improper 
cartridge detection (Black)

F2

70

Display

Lamp/Message

Phenomenon Detail

When detecting the normal 
CRUM of the cartridge, 
improper data are detected 
in the CRUM contents.

Section

Developing

Case 1

Cause

Insertion of an improper 
cartridge. Developing unit 
trouble

Check & 
Remedy

Replace the developing 
unit.

Main 
code

Sub 

code

Title

Color image density sensor 
trouble (Calibration plate surface 
reflection ratio abnormality)

Main 
code

Sub 

code

Title

Developing unit improper 
cartridge detection (Cyan)

F2

71

Display

Lamp/Message

Phenomenon Detail

When detecting the normal 
CRUM of the cartridge, 
improper data are detected 
in the CRUM contents.

Section

Developing

Case 1

Cause

Insertion of an improper 
cartridge. Developing unit 
trouble

Check & 
Remedy

Replace the developing 
unit.

Main 
code

Sub 

code

Title

Developing unit improper 
cartridge detection (Magenta)

F2

72

Display

Lamp/Message

Phenomenon Detail

When detecting the normal 
CRUM of the cartridge, 
improper data are detected 
in the CRUM contents.

Section

Developing

Case 1

Cause

Insertion of an improper 
cartridge. Developing unit 
trouble

Check & 
Remedy

Replace the developing 
unit.

Main 
code

Sub 

code

Title

Developing unit improper 
cartridge detection (Yellow)

F2

73

Display

Lamp/Message

Phenomenon Detail

When detecting the normal 
CRUM of the cartridge, 
improper data are detected 
in the CRUM contents.

Section

Developing

Case 1

Cause

Insertion of an improper 
cartridge. Developing unit 
trouble

Check & 
Remedy

Replace the developing 
unit.

Main 
code

Sub 

code

Title

Developing unit CRUM trouble 
(Black)

F2

74

Display

Lamp/Message

Phenomenon Detail

CRUM read/write error

Section

Developing

Case 1

Cause

Improper connection or 
disconnection of the 
connector and the harness 
between the PCU and the 
CRUM.

Check & 
Remedy

Check the connector and 
the harness between the 
PCU and the CRUM.

Case 2

Cause

Developing unit trouble

Check & 
Remedy

Replace the developing 
unit.

Case 3

Cause

Control PWB (PCU) 
trouble

Check & 
Remedy

Replace the PCU PWB.

Summary of Contents for AR-BC320

























































































































































































































































































































































Reviews:

No comments