manualshive.com logo in svg

Sharp AR-BC320, Service Manual, Page: 233 / 344

Share
Download
Sharp AR-BC320 Service Manual Download Page 233

AR-BC320  SIMULATION  9 - 79

2. Use "fcopy" command on the PC side to download the 

firmware file.

When the firmware data are normally downloaded and written into 
the Flash ROM, "COMPLETE" is displayed.

In case of an error, the following message is displayed.

∗

When the Flash ROM kind is improper:
 "ROM KIND ERROR" is displayed.

∗

When an error occurs during initializing the Flash ROM:
"FLASH ERROR" is displayed.

∗

When an error occurs during verifying:
"UPDATE ERROR" is displayed.

When the printer NVRAM is normally cleared, "COMPLETE" is 
displayed. In case of an error, "ERROR" is displayed.

67

67

-01

Purpose

Operation test/check

Function 
(Purpose)

Used to check the operations of printer DRAM read/
write.

Section

Printer

Item

Operation

Operation/
Procedure

When the machine enters the simulation mode, the 
printer DRAM read/write operation check is started.
After completion of check, "ERROR" or "MEMORY 
SIZE" is displayed. If no memory is installed, "NA" is 
displayed.

67

-11

Purpose

Setting

Function 
(Purpose)

Used to set the printer parallel I/F SELECT IN 
signal.

Section

Printer

Item

Operation

Operation/
Procedure

Enter the set value with the 10-key, and press the 
[OK] key.
When a trouble occurs in communication between 
PC and the printer by use of the printer parallel I/F, 
change the setup content of this simulation.

Display

Content

Set range

Default

A

SELECT-IN 
(0:OFF 1:ON)

Centro I/F SELECT IN 
signal YES/NO setting

0 –  1

1

67

-14

Purpose

Version up

Function 
(Purpose)

Used to perform version up of the firmware. 
(Printer)

Section

Firmware (Printer)

Item

Operation

Operation/
Procedure

1. When the machine enters the simulation mode, 

it enters the printer firmware version up mode at 
the same time.

67

-17

Purpose

Data clear

Function 
(Purpose)

Used to clear NVRAM. (Printer)

Section

Printer

Item

Others

Operation/
Procedure

1. Press the [EXECUTE] key. 

The confirmation message to clear is displayed.

2. Select YES/NO to clear the NVRAM.

YES: Clear
NO: Not clear

Summary of Contents for AR-BC320

























































































































































































































































































































































Reviews:

No comments