manualshive.com logo in svg

Sharp AR-BC320, Service Manual, Page: 11 / 344

Share
Download
Sharp AR-BC320 Service Manual Download Page 11

AR-BC320  SPECIFICATIONS  3 - 2

(6) Warm-up

(7) Jam recovery time

(8) Image chip (Printable area)

∗

In A3/11" x 17" full image copy, there is no image chip in A3/
WLT image.

∗

When outputting cut position marks, printing can be made in the
range of image chip specification.

∗

When using RADF, however, A3 full image copy cannot be
made. (OC mode only)

(9) Printer controller

(10) Power source

(11) Power consumption

(12) Noise/Ozone

(13) External dimensions

(14) Weight

(15) Machine occupying dimensions

B. Paper feed unit

(1) Machine paper feed tray

*1: 1g/m

2

 = 0.265625 lbs (applied to the flowing subjects)

(2) Manual feed tray (Bypass tray)

Detection of 8.5 x 14 can be changed to detection of 8.5 x 13 (216
x 330) with the simulation.

Warm-up time

99sec or less

Pre-heat function

Yes

With the left cover and front 
cabinet open

About 60 sec

Left for 60 sec
Normal condition

With the right cover open

About 8 sec

Full size

Total circumference 4mm ± 2mm
Only when A3 full image is outputted, 6mm or less in 
total.

Type

Built-in

CPU

Power PC 7410-500 MHz

Memory

640MB

Add. memory slot

2 slot (For SEC: N/A)

Font

80 fonts (PCL5-c), 136fonts (PS3: option)

NIC

Software NIC is standard

Voltage

100 V – 127 V

Frequency

50/60 Hz

Power cord

Inlet type
• For optional stand (for AC power supply /

Fax Box)

∗

Nighttime mode should be supported.

Max. power consumption

1.5 kW

Sleep mode

80W or less

Noise

Operating

B/W

68dB or less (First)

Color

63dB or less (First)

Stand-by

55dB or less

Sleep

40dB or less

Ozone

0.02g/m

3

 or less

External dimensions

670 x 676 x 778 mm 
(26-3 x 26-5/8 x 30-5/8 inch)

Weight

Copier body: 85 kg (187.5 lbs.)
Copier body + photoconductor: 88 kg (194.0 lbs.)
Copier body + photocon toner: 
95 kg (209.4 lbs.)

Machine occupying dimensions 
(Machine only, with the trays full open)

1,349 x 676 mm
(53-1/8 x 26-5/8 inch)

Paper feed system

1-stage tray

Paper feed size

AB series: A3, B4, A4, A4R, B5, A5, 
8.5” x 11”, EXTRA
Inch series: 11" x 17", 8.5" x 14", 
8.5" x 13", 8.5" x 11", 8.5" x 11"R, 
8.5" x 5.5", A4, EXTRA
(EXTRA setting)
AB tab setting section: 
A3, B4, A4, A4R, B5, B5R, A5, EXTRA
Inch tab setting section: 
11" x 17", 8.5" x 14", 8.5" x 13", 
8.5" x 11", 8.5" x 11"R, 8.5" x 5.5", 
7.25” x 10.5”R, EXTRA

Paper feed capacity*

1

550 sheets (64g/m

2

 (17 lbs.) paper)

500 sheets (80g/m

2

 (21 lbs.) paper, 

recommended paper for color)

Weight of paper 
suitable for paper feed

64 to 105g/m

2

 (17 to 28 lbs)

Paper kind

Normal paper (including recommended 
paper for color), recycled paper, printed 
paper, punched paper, color paper, 
letter head

Paper size detection

Slide lever detection

Paper size selection

Use selection 

Dehumidifier

Service kit

Remaining quantity 
detection

Yes (0, 25%, 50%, 75%, Full, 5 steps)

Initial size when 
shipping

A3 (11" x 17")

Tray attach/detach

Possible

Universal support

Universal tray (free size)

Transport 
reference

Center reference

Paper feed 
capacity

250 sheets (80g/m

2

), 300 sheets (64g/m

2

), 

100 sheets (Postcard)

Paper size

A3W to A6R

Paper weight

64 to 300g/m

2

 / 17 to 80lbs specified paper 

for color

Paper kind

Normal paper (including recommended paper 
for color), OHP1, OHP2. heavy paper 1 (106 
to 200g/m

2

 (28 to 54 lbs.)), heavy paper 2 

(201 to 300g/m

2

 (54 to 80 lbs.)), envelope,  

specified size paper

Paper size 
detection

Inch series: 12" x 18", 11" x 17", 8.5" x 14", 
8.5" x 11", 8.5" x 11"R, 7.25" x 10.5"R, 
8.5" x 5.5", A3, B4, A4, B5, A6R
AB series: A3W, A3, B4, A4, A4R, B5, A5, 
A6R, 11" x 17", 8.5" x 14", 8.5" x 11", 
7.25" x 10.5"R

Manual feed 
size setup

Yes (Ignoring automatic setup)
Selected with key operation.

Summary of Contents for AR-BC320

























































































































































































































































































































































Reviews:

No comments