manualshive.com logo in svg

Sharp AR-BC320, Service Manual, Page: 235 / 344

Share
Download
Sharp AR-BC320 Service Manual Download Page 235

AR-BC320  SIMULATION  9 - 81

3. Set the color patch image (adjustment pattern) printed in SIM 

67-25 on the document table, and press [EXECUTE] key.
[EXECUTE] key is highlighted and sampling is executed.

4. After completion of the operation, [EXECUTE] key is returned 

to the normal display, and the sampling result is displayed.
When [REPEAT] key is pressed, the process returns to 
procedure 3). 

5. Press the [OK] key.

The displayed target value is saved to the backup area as the 
target value. 

∗

For BASE, only the sampling result display menu is displayed. 

1. Press the [EXECUTE] key.

2. Select [YES]. (If [NO] is selected, the display returns to the 

initial display.)

The value is reset to the standard value, and the data are saved to 
the backup area.

 

Printer screen selection. When DEF is 0, it is the same as the 
conventional screen. When DEF is 1, it is an option screen with 
improved grainy. (However, the number of lines of the screen is 
reduced.)

2. Insert the copy source ROM into the font ROM socket.
3. Press the [EXECUTE] key.
4. ROM data initializing, writing, and verifying are performed.

∗

When the result is displayed, CA key and the CUSTOM 
SETTINGS key become valid.

67

-27

Purpose

Adjustment

Function 
(Purpose)

Used to display and register the scanner target 
value (for servicing) of the printer engine automatic 
density adjustment. (Conforms to the service button 
of SIM 67-24. (The serviceman can scan the target 
value.))

Operation/
Procedure

1. Select a color for sampling.
2. Press [SETUP] key.

Display data

Display content

B

Target value of point B

C

Target value of point C

D

Target value of point D

E

Target value of point E

F

Target value of point F

G

Target value of point G

H

Target value of point H

I

Target value of point I

J

Target value of point J

K

Target value of point K

L

Target value of point L

M

Target value of point M

N

Target value of point N

O

Target value of point O

BASE

Base sampling value

67

-28

Purpose

Adjustment

Function 
(Purpose)

Used to reset the scanner target value (for servicing) 
in the printer engine automatic density adjustment to 
the standard value. (Reset to the standard value of 
SIM67-27. (The value is reset to the factory setting.))

Operation/
Procedure

The registration target value set with SIM67-27 
(Printer engine automatic density adjustment 
scanner target value (for servicing) display & 
registration) is reset to the standard value.

67

-29

Purpose

Setting

Function 
(Purpose)

Used to set the printer screen mode.

Operation/
Procedure

1. Select a set item with the scroll key.
2. Enter a set value with the 10-key.
3. Press the [OK] key.

Item

Content

Set 

range

Default

A

4BIT PHOTO AREA

0:PHOTO1  1:PHOTO2

0 –  1

1

B

4BIT GRAPHICS AREA 0:GRAPHICS1  

1:GRAPHICS2

0 –  1

0

C

4BIT CAD SCREEN

0:CAD1  1:CAD2

0 –  1

1

67

-40

Purpose

Setting

Function 
(Purpose)

Used to copy the scanner destination. (Flash writing)

Section

Flash ROM (Scanner)

Item

Data

Writing

Operation/
Procedure

1. Insert a new ROM of copy destination into the 

socket of the firm ROM.

Summary of Contents for AR-BC320

























































































































































































































































































































































Reviews:

No comments