manualshive.com logo in svg

Sharp AR-BC320, Service Manual, Page: 38 / 344

Share
Download
Sharp AR-BC320 Service Manual Download Page 38

AR-BC320  EXTERNAL VIEW AND INTERNAL STRUCTURE  6 - 9

H. PWB 1

25

No. 1 cassette paper feed detection

Detects paper exit from No. 1 paper tray.

PFD1

Photo sensor (Photo 
transmission)

26

Manual feed paper width detection

Detects the paper width.

MPWS

Volume (Variable 
resistor)

27

No. 1 cassette lift-up upper limit detection Detects the upper limit position of paper.

LUD1

Photo sensor (Photo 
transmission)

28

PS front sensor

Detects paper in front of PS.

PPD2

Photo sensor (Photo 
transmission)

29

No. 1 cassette paper empty detection

Detects paper empty on the paper tray.

PED1

Photo sensor (Photo 
transmission)

31

Belt lift-up upper limit detection

Detects lift-up or lift-down of the transfer belt. 

BLUD

Photo sensor (Photo 
transmission)

32

Belt waste toner full detection

Detects belt waste toner full.

BTNF

Contact switch

33

Color toner concentration (process 
control) sensor/Auto image Reg.

Detects the toner patch density (color toner) in image density 
correction operation. 2-sensors on PWB.

PCS_C

Photo sensor (Photo 
transmission)

34

Lower heat roller thermistor

Detects the temperature on the heat roller surface.

THSD

Thermistor

35

Lower heat roller thermostat

Detects an abnormally high temperature and turns off the heater lamp. HLTS2

Thermostat
Thermal switch

36

Machine paper exit sensor 1

Detects discharged paper.

POD1

Photo sensor (Photo 
transmission)

37

Upper heat roller thermistor

Detects the temperature on the heat roller surface.

THSU

Thermistor

38

Upper heat roller thermostat

Detects an abnormally high temperature and turns off the heater lamp. HLTS1

Thermostat
Thermal switch

39

Main switch

Turns ON/OFF the main power.

MSW

Seesaw switch

40

Front door open detection

Detects open/close of the front door.

DSWF

Micro switch

41

Paper exit door open detection

Detects open/close of the paper exit door.

DSWL

Micro switch

42

Face-up paper exit tray full detection

Detects full of the face-up paper exit tray.

TFD

Photo sensor (Photo 
transmission)

43

Machine paper exit sensor 2

Detects discharged paper.

POD2

Photo sensor (Photo 
transmission)

44

Black toner concentration sensor

Detects black patch density for toner concentration

PCS_B

—

No.

Parts

Code, signal 

name

Type

Name

Function

1

2

5

6

3

4

8

7

9

10

12

11

13

14

Front / right side / top view

Summary of Contents for AR-BC320

























































































































































































































































































































































Reviews:

No comments