manualshive.com logo in svg

Sharp AR-BC320, Service Manual, Page: 166 / 344

Share
Download
Sharp AR-BC320 Service Manual Download Page 166

AR-BC320  SIMULATION  9 - 12

50

10

Used to adjust the print image 
center position. (Adjustment is 
performed in each paper feed 
position separately.)

Adjustment

Image process (ICU) 

Picture quality Image position

12

Used to adjust the print image 
center position. (The adjustment 
is performed in each document 
mode separately.)

Adjustment

Image process (ICU) 

Picture quality Image position

20

Used to adjust the image 
registration. (Manual 
adjustment)

Adjustment

Picture quality Image position

22

Used to adjust the image 
registration. (Automatic 
adjustment)

Adjustment

Picture quality Image position

24

Used to display the adjustment 
data of automatic registration.

Adjustment

Picture quality Image position

27

Used to adjust image loss in the 
FAX/scanner mode.

Adjustment

FAX/Scanner

Picture quality

28

Used to adjust automatic void 
(service installation adjustment).

Adjustment

Picture quality Image position

51

1

Used to adjust the transfer 
voltage ON timing.

Adjustment

Process 
(Photoconductor, 
developing, transfer, 
cleaning)

Transfer

Operation

2

Used to adjust the contact 
pressure of paper on the resist 
roller of each section (each 
paper feed and duplex feed of 
the copier).
(This adjustment is required 
when the print image position 
variations are considerably great 
or when paper jams occur 
frequently.)

Adjustment

Paper transport 
(Paper exit, 
switchback, transport) 

Operation

52

1

Used to adjust the duplex print 
mode stacking capacity (Used to 
adjust the stop position of the 
duplex unit paper tray width 
alignment plate. The home 
position of the width alignment 
plate is changed by software.)

Adjustment

Duplex

Operation

53

1

Used to adjust the document 
stop position in each operation 
mode of the RADF.

Adjustment

RADF

Operation

2

Used to adjust the optical sensor 
sensitivity in RADF.

Adjustment

RADF

Operation

60

1

Used to check the operation of 
ICU PWB image DRAM read/
write.

Operation test/
check

ICU (Memory)

Operation

61

4

Used to adjust the scanner 
(writing) unit (LED array unit) 
skew.

Adjustment

Scanner (writing)

Operation

63

1

Used to check the result of 
shading correction. (The 
shading correction data are 
displayed.)

Adjustment/
Setting/Operation 
data output, check 
(display, print)

Scanner (Exposure)

Operation

3

Used to adjust the CCD color 
balance (gamma).

Adjustment

Scanner 
(Image scanning)

Picture quality Color balance

5

Used to set the CCD color 
balance (gamma) default.

Setting

Scanner 
(Image scanning)

Picture quality Color balance

6

Used to check the color balance 
(gamma) check patch.

Adjustment/
Setting/Operation 
data output, check 
(display, print)

Image process (ICU)

Picture quality Color balance

Code

Function (Purpose)

Purpose

Section

Item

Main Sub

Summary of Contents for AR-BC320

























































































































































































































































































































































Reviews:

No comments