manualshive.com logo in svg

Sharp AR-BC320, Service Manual, Page: 149 / 344

Share
Download
Sharp AR-BC320 Service Manual Download Page 149

AR-BC320  SETTING AND ADJUSTMENTS  8 - 42

Enable when “1” is set in SIM 26-54.

1) Execute SIM 67-24.

2) Press EXECUTE key on the LCD display to output a patch

self-print for the scanner adjustment. The process control is
executed. When the display of "NOW PROCON EXECUTING"
is gone, the color patch for the printer adjustment written as
"PRINTER CALIBRATION" is outputted. (Note that it is
different from the color patch for the copy adjustment. If it is
erroneously set, an error display is made.)

3) Set the print made in procedure 2) on the table glass with the

higher density side on the paper exit side.
Put five sheets of white paper on the print, select FACTORY
key, and press EXECUTE  key again to make an output.

4) After making an output print, press OK key on the LCD

display. Press CA key on the main unit to terminate the
simulation.

(Document reference)

5) At the end, check that the printed color balance check patch is

within the following specifications. 

The print density is gradually changed from the lower area to the
higher area without reversing of the change direction.

The density level of each color is virtually same.

Patch B may not be printed.

The performance of the color balance adjustment can be checked
more precisely by printing the color balance adjustment sheet with
SIM 67-25 and comparing the black patch color balance of each
process (CMY) with the black patch.

ADJ 20

Printer color balance adjustment

ADJ 20A

Printer automatic color balance adjustment

[Enter SIM 67-24, 
and press EXECUTE key.]

[Set paper and select FACTORY key.]

[Press OK key.]

[Press CA key.]

Max

A

B

C

D

E

F

G

H

I

J

K

L

M

N

O

C

M

Y

Bk

1) The max. density
     section is not blurred.

3) Patch for each of C, M, Y, BK

• The patch density is identical between patches or not reversed.
• The patch density is changed gradually.

2) Patch C or D of each of Y, C, M, 
    and BK is very slightly copied.

High density

Low density

Fig. 1 PG image

Max

A

B

C

D

E

F

G

H

I

J

K

L

M

N

O

C

M

Y

Bk

1) The max. density section is not blurred.

4) Patch for each of C, M, Y, BK
• The patch density is identical between patches or not reversed.
• The patch density is changed gradually.

3) Patch C or D of each of Y, C, M, 
    and BK is very slightly copied.

High density

Low density

CMY
mixed
color

Summary of Contents for AR-BC320

























































































































































































































































































































































Reviews:

No comments