manualshive.com logo in svg

Sharp AR-BC320, Service Manual, Page: 276 / 344

Share
Download
Sharp AR-BC320 Service Manual Download Page 276

AR-BC320  ROM VERSION UP  12 - 3

Relationship between copy (write) method and copy contents

(1)-a Method of writing the program data from a PC to the ICU MAIN PWB Flash ROM (Making of source ROM)

The program for each PWB and the Flash ROM copy program are copied into the Flash ROM on the Write side socket.

(1)-b Method of writing the program data from PC to the Flash ROM on the ICU PWB

The program for each PWB is copied to the Flash ROM on the Write socket. 

PC side

Write side Flash Rom (Flash ROM B)

Note

Content

File name

Name

Capacity

Copied content

Program for 
PCU Flash 
ROM

Program for 
Flash ROM copy 
(ROM to ROM)

xPcuxxx_src.pgm

For PCU 
Flash ROM

32Mbit x 2 Program for 

PCU Flash 
ROM

Program for 
Flash ROM copy 
(ROM to ROM)

The ICU Flash ROM with 
the copy (write) program 
in it must be connected 
to the Read side Flash 
ROM socket. When 
shipping, from the 
factory, the copy (write) 
program is provided for 
use.
By this method with two 
Flash ROM sockets on 
the ICU PWB, the Flash 
ROM for copying is 
made.

Program for 
ICU Flash 
ROM

Program for 
Flash ROM copy 
(ROM to ROM)

xlcuxxx_src.pgm

For ICU 
Flash ROM

32Mbit x 2 Program for 

ICU Flash 
ROM

Program for 
Flash ROM copy 
(ROM to ROM)

Program for 
operation 
control 
Flash ROM

Program for 
Flash ROM copy 
(ROM to ROM)

xOpexxx_src.pgm

For 
operation 
control 
Flash ROM

32Mbit x 2 Program for 

operation 
control 
Flash ROM

Program for 
Flash ROM copy 
(ROM to ROM)

Program for 
scanner 
control 
Flash ROM

Program for 
Flash ROM copy 
(ROM to ROM)

WScnXXX_src.pgm For 

scanner 
control 
Flash ROM

32Mbit x 2 Program for 

scanner 
control 
Flash ROM

Program for 
Flash ROM copy 
(ROM to ROM)

Program for 
FAX control 
Flash ROM

Program for 
Flash ROM copy 
(ROM to ROM)

For FAX 
control 
Flash ROM

32Mbit x 2 Program for 

FAX control 
Flash ROM

Program for 
Flash ROM copy 
(ROM to ROM)

PC side

Write side Flash Rom (Flash ROM D)

Note

Content

File name

Name

Capacity

Copied content

Program for PCU 
PWB Flash ROM

xpcuxxx_d.pgm

For PCU 
Flash ROM

8Mbit

Program for PCU 
Flash ROM

The ICU MAIN PWB 
Flash ROM with the copy 
(write) program in it must 
be connected to the 
Read side Flash ROM 
socket. When shipping, 
from the factory, the copy 
(write) program is 
provided for use.

Program for ICU 
PWB Flash ROM

xIcuxxx_d.pgm

For ICU 
Flash ROM

32Mbit x 2 Program for ICU 

Flash ROM

Program for 
operation control 
Flash ROM

xOpexxx_d.pgm

For operation 
control Flash 
ROM

16Mbit x 2 Program for 

operation control 
Flash ROM

Program for 
scanner control 
Flash ROM

WScnXXX_d.pgm

For scanner 
control Flash 
ROM

16Mbit x 2 Program for 

scanner control 
Flash ROM

Program for FAX 
control Flash 
ROM

For FAX 
control Flash 
ROM

8Mbit x 2

Program for FAX 
control Flash 
ROM

Summary of Contents for AR-BC320

























































































































































































































































































































































Reviews:

No comments