Sharp AR-BC320 Service Manual Download Page 249

Page: 249 / 344

AR-BC320 TROUBLESHOOTING 11 - 2

5. List

Main
code

Sub

code

Content

PCU PWB error

Image density sensor error/Transfer charger error
(Black)

Image data memory trouble

ICU gate array trouble

Shading trouble (Black correction)

Shading trouble (White correction)

LED controller initial trouble (Black)

LED controller initial trouble (Cyan)

LED controller initial trouble (Magenta)

LED controller initial trouble (Yellow)

LED controller output trouble (Black)

LED controller output trouble (Cyan)

LED controller output trouble (Magenta)

LED controller output trouble (Yellow)

LED control ASIC connection abnormality

ICU PWB matching error

Color correction data writing abnormality

Color correction data transfer abnormality

ICU-SCN communication trouble (ICU detection)

ICU-PCU communication trouble (ICU detection)

Finisher communication trouble (PCU detection)

Finisher transport motor trouble (Finisher detection)

Finisher paddle motor trouble

Finisher slide motor trouble

Finisher staple motor abnormality (Finisher
detection)

Finisher bundle process motor abnormality (Finisher
detection)

Finisher tray lift motor abnormality (Finisher
detection)

Finisher front alignment motor abnormality (Finisher
detection)

Finisher rear alignment motor abnormality (Finisher
detection)

Finisher fold sensor trouble

Finisher punch unit communication trouble

Finisher punch side registration motor trouble

Finisher punch motor trouble

Finisher punch side registration sensor trouble

Finisher punch registration sensor trouble

Finisher backup RAM trouble

Finisher punch backup RAM trouble

Finisher punch dust sensor trouble

Finisher punch power disconnection trouble

Sorter push bar motor trouble

Sorter bin shift motor trouble

Automatic adjustment trouble of the paper sensor in
the sorter bin

Process thermistor breakdown

Toner empty sensor abnormality (Black)

Toner empty sensor abnormality (Cyan)

Toner empty sensor abnormality (Magenta)

Toner empty sensor abnormality (Yellow)

Black image density sensor trouble (Transfer belt
surface reflection ratio abnormality)

Color image density sensor trouble (Calibration plate
surface reflection ratio abnormality)

Process humidity sensor breakdown

Developing unit improper cartridge detection (Black)

Developing unit improper cartridge detection (Cyan)

Developing unit improper cartridge detection
(Magenta)

Developing unit improper cartridge detection
(Yellow)

Developing unit CRUM trouble (Black)

Developing unit CRUM trouble (Cyan)

Developing unit CRUM trouble (Magenta)

Developing unit CRUM trouble (Yellow)

Trouble of image density sensor for registration
(Transfer belt surface reflection ratio abnormality)

Half-tone process control 1st batch error (Black)

Half-tone process control 1st batch error (Cyan)

Half-tone process control 1st batch error (Magenta)

Half-tone process control 1st batch error (Yellow)

Half-tone process control 2nd batch error (Black)

Half-tone process control 2nd batch error (Cyan)

Half-tone process control 2nd batch error (Magenta)

Half-tone process control 2nd batch error (Yellow)

Half-tone process control limit error

Cassette 1 lift up trouble

ICU-FAX communication trouble (ICU detection)

FAX expansion flash memory abnormality (ICU
detection)

FAX MODEM operation abnormality

FAX write protect release

Improper combination of the TEL/LIU PWB and the
FAX soft switch.

The FAX-BOX PWB is not one for the AR-BC320.
(FAX detection)

Improper combination of the FAX-BOX destination
data and the main unit destination data

ICU-PRT communication trouble (ICU detection)

PRT DRAM trouble

NIC port check error

HDD trouble (PRT controller detection)

Thermistor open (HL1)

Thermistor open (HL2)

Fusing section high temperature trouble (HL1)

Fusing section high temperature trouble (HL2)

Fusing section low temperature trouble (HL1)

Fusing section low temperature trouble (HL2)

Five continuous detections of POD1 not-reached jam

Mirror feed trouble

Mirror return trouble

Paper feed motor lock trouble

Transfer belt lift motor trouble

Transfer belt motor trouble

Shift motor trouble

Full wave signal not provided

Full wave signal width abnormality

Main power switch abnormality detection

RIC copy inhibit signal reception

ICU-OPE communication trouble (ICU/OPE
detection)

RTC read trouble

Main
code

Sub

code

Content

Summary of Contents for AR-BC320

























































































































































































































































































































































Search results

Summary of Contents for AR-BC320

Reviews:

Sharp AR-BC320, Service Manual, Page: 249 / 344

Search results

Summary of Contents for AR-BC320

Reviews: