Sharp AR-BC320 Service Manual Download Page 258

Page: 258 / 344

AR-BC320 TROUBLESHOOTING 11 - 11

Main
code

Sub

code

Title

Automatic adjustment trouble of
the paper sensor in the sorter bin

Display

Lamp/Message

Phenomenon Detail

Sensor output abnormality
when adjusting the sensor
detection level.

Section

Sorter

Common

Check

Execute SIM 3-2 to check
the sensor output.

Case 1

Cause

Trouble of the paper sensor
in the bin.

Check &
Remedy

Replace the paper sensor in
the bin.

Case 2

Cause

Sorter controller PWB
trouble

Check &
Remedy

Replace the sorter
controller PWB, and
perform the sensor
sensitivity adjustment in the
bin and the guide bar motor
oscillation range
adjustment.

Main
code

Sub

code

Title

Process thermistor breakdown

Display

Lamp/Message

Phenomenon Detail

Process thermistor open

Section

Drum cartridge

Case 1

Cause

Process thermistor trouble

Check &
Remedy

Replace the process
thermistor.

Case 2

Cause

Disconnection of the
process thermistor
harness.

Check &
Remedy

Check connection of the
connector and the harness
of the process thermistor.

Case 3

Cause

PCU PWB trouble

Check &
Remedy

Replace the PCU PWB.

Main
code

Sub

code

Title

Toner empty sensor abnormality
(Black)

Display

Lamp/Message

Phenomenon Detail

Toner empty sensor output
abnormality

Section

Cartridge

Case 1

Cause

Connector harness
trouble, connector
disconnection

Check &
Remedy

1. Check connection of the

toner empty sensor.

→

Connect it properly.

2. Check connection of the

connector harness to
the PCU PWB.

→

Connect it properly.

3. Check connection of the

cartridge.

→

Connect it

properly.

4. Check for disconnection

of the harness.

→

Replace the harness.

Case 2

Cause

Cartridge trouble

Check &
Remedy

Replace the cartridge.

Main
code

Sub

code

Title

Toner empty sensor abnormality
(Cyan)

Display

Lamp/Message

Phenomenon Detail

Toner empty sensor output
abnormality

Section

Cartridge

Case 1

Cause

Connector harness
trouble, connector
disconnection

Check &
Remedy

1. Check connection of the

toner empty sensor.

→

Connect it properly.

2. Check connection of the

connector harness to
the PCU PWB.

→

Connect it properly.

3. Check connection of the

cartridge.

→

Connect it

properly.

4. Check for disconnection

of the harness.

→

Replace the harness.

Case 2

Cause

Cartridge trouble

Check &
Remedy

Replace the cartridge.

Summary of Contents for AR-BC320

























































































































































































































































































































































Search results

Summary of Contents for AR-BC320

Reviews:

Sharp AR-BC320, Service Manual, Page: 258 / 344

Search results

Summary of Contents for AR-BC320

Reviews: