manualshive.com logo in svg

Sharp AR-BC320, Service Manual, Page: 310 / 344

Share
Download
Sharp AR-BC320 Service Manual Download Page 310

AR-BC320  ELECTRIC DIAGRAM  13 - 24

5. Signal list

Signal name

Name

Function/Operation

Section

AOSW

ADF open switch

Detects ADF open.

RADF

APAM

Alignment motor

Aligns paper in ADU.

AR-D19

APHPS

Alignment plate home position detection

Detects the alignment plate in ADU.

AR-D19

APPD1

ADU transport sensor 1

Detects paper transport in ADU.

AR-D19

APPD2

ADU transport sensor 2

Detects paper transport in ADU.

AR-D19

ARHPS 

Bundle roller HP sensor

AR-F13

AS 

Alignment tray sensor

AR-F13

ATM

ADU transport motor

Drives the paper transport section in ADU.

AR-D19

ATRC

ADU transport clutch

Controls ON/OFF of the transport roller in ADU.

AR-D19

BDD

Door open detection 1

Detects upper door open.

AR-RB1

BDD2

Door open detection 2

Detects left door open.

AR-RB1

BES 

Tray paper sensor

AR-F13

BGSOL

Gate solenoid 

Switches straight or reverse paper exit. 

AR-RB1

BIM

Paper entry motor

Transports paper in the paper entry section.

AR-RB1

BLUD

Belt lift-up upper limit detection

Detects if the transfer belt is lifted up or down.

Main machine

BLUM

Belt lift-up motor

Lifts the transfer belt unit.

Main machine

BPFD

Full sensor

Detects paper full on the tray.

AR-RB1

BPOD

Paper exit sensor

Detects paper exit.

AR-RB1

BPPD1

Transport sensor 1

Detects paper transport.

AR-RB1

BPPD2

Transport sensor 2

Detects paper transport.

AR-RB1

BPRD

Reverse section sensor

Detects paper presence in the reverse section.

AR-RB1

BRM

Upper reverse motor

Transports paper in the upper section.

AR-RB1

BTM

Transport belt motor

Drives the transfer belt.

Main machine

BTM

Lower reverse motor

Transports paper in the lower section.

AR-RB1

BTNF

Belt waste toner detection

Detects belt waste toner full.

Main machine

C1SS1

1 cassette paper size detection 1

Detects the paper size which is set by the paper size set 
block.

Main machine

C1SS2

1 cassette paper size detection 2

Detects the paper size which is set by the paper size set 
block.

Main machine

C1SS3

1 cassette paper size detection 3

Detects the paper size which is set by the paper size set 
block.

Main machine

C1SS4

1 cassette paper size detection 4

Detects the paper size which is set by the paper size set 
block.

Main machine

CALS

Calibration plate open/close solenoid

Switches image density sensors.

Main machine

CPFC1

Paper feed clutch

Transmits the paper feed motor power to each transport 
roller. (Controls ON/OFF.)

Main machine

DCSPSx

Paper remaining quantity sensor

Detects the remaining quantity of paper.

AR-D17/D18

DCSSx

Paper size sensor

Detects the paper size.

AR-D17/D18/D19

DDOPD

Door open sensor

Detects opening of the right door.

AR-D17/D18

DEM

Reverse motor

Reverses or discharges documents.

RADF

DEOS

Paper exit open sensor

Detects opening of the paper exit cover.

RADF

DES

Paper exit sensor

Detects that a document has been transported to the 
paper exit sensor section.

RADF

DFM

Paper feed motor

Feeds a document from the tray.

RADF

DFOS

Paper feed open sensor

Detects opening of the paper feed cover.

RADF

DFSW

Paper feed open switch

Detects opening of the paper feed cover.

RADF

DH

Dehumidifier heater

Dehumidifier heater for the machine cassette.

Main machine

DLMx

Lift motor

Drives the lift plate.

AR-D17/D18/D19

DLS1

Tray document length sensor 1

Detects the document length on the tray. (Short)

RADF

DLS2

Tray document length sensor 2

Detects the document length on the tray. (Long)

RADF

DLUDx

Paper upper limit sensor

Detects the paper upper limit position.

AR-D17/D18/D19

DM

Paper feed drive motor

Drives the paper feed section and the paper transport 
section.

AR-D17/D18/D19

DM_C

Drum motor (C) 

Drives the Cyan photoconductor unit.

Main machine

DM_K

Drum motor (K)

Drives the Black photoconductor unit.

Main machine

DM_M

Drum motor (M)

Drives the Magenta photoconductor unit.

Main machine

DM_Y

Drum motor (Y)

Drives the Yellow photoconductor unit.

Main machine

DPEDx

Paper empty sensor

Detects paper presence on the paper tray.

AR-D17/D18/D19

DPFCx

Paper feed clutch

Controls ON/OFF of the paper feed roller.

AR-D17/D18/D19

DPFSx

Pickup solenoid

Presses the paper pickup roller onto paper.

AR-D17/D18/D19

DPPD1

Paper transport sensor 1

Detects paper transport.

AR-D17/D18/D19

Summary of Contents for AR-BC320

























































































































































































































































































































































Reviews:

No comments