Sharp AR-BC320 Service Manual Download Page 250

Page: 250 / 344

AR-BC320 TROUBLESHOOTING 11 - 3

6. Details

EEPROM read/write error (ICU detection)

EEPROM check sum error (ICU detection)

Production No. data discrepancy (ICU

⇔

ICU)

EEPROM read/write error (SCN detection)

EEPROM check sum error (SCN detection)

EEPROM read/write error (PCU detection)

EEPROM check sum error (PCU detection)

ADU alignment plate operation abnormality

ADF communication trouble

ADF resist sensor defect

ADF repulsion sensor defect

ADF timing sensor defect

Paper feed motor operation abnormality

Desk communication trouble

Desk tray 1 lift motor trouble

Desk tray 2 lift motor trouble

Desk tray 3 lift motor trouble

Desk transport motor trouble

RIC communication trouble

CPT-ASIC trouble (MFP PWB trouble)

Main
code

Sub

code

Title

PCU PWB error

Display

Lamp/Message

Phenomenon Detail

When the power is turned
on, conformity of the PCU
PWB and the PCU ROM is
checked to be found that
there is no conformity.

Section

PCU PWB

Case 1

Cause

PCU PWB trouble

Check &
Remedy

Replace the PCU PWB.

Case 2

Cause

PCU PWB mistaken

Check &
Remedy

Replace the PCU PWB.

Main
code

Sub

code

Title

Image density sensor error/
Transfer charger error (Black)

Display

Lamp/Message

Phenomenon Detail

Black image density
sensor trouble /Transfer
trouble (Black) /The
deference between the
transfer belt surface
detection level and the
black toner patch density
detection level is normal.
(Judged in black image
density sensor calibration)

Section

Transfer

Case 1

Cause

Black image density
sensor trouble

Check &
Remedy

Black density image sensor
cleaning, replacement

Case 2

Cause

Transfer voltage trouble

Check &
Remedy

Check and adjust the
transfer voltage.

Case 3

Cause

High voltage PWB trouble

Check &
Remedy

Replace the high voltage
PWB.

Main
code

Sub

code

Content

Case 4

Cause

Transfer unit trouble

Check &
Remedy

Check the transfer belt
surface for dirt and
scratches.
Replace the transfer belt,
replace the cleaning blade,
replace the transfer unit.

Case 5

Cause

PCU PWB trouble

Check &
Remedy

PCU PWB replacement

Case 6

Cause

Photoconductor unit
trouble

Check &
Remedy

Replace the
photoconductor unit.

Case 7

Cause

Developing unit trouble

Check &
Remedy

Replace the developing
unit

Case 8

Cause

Connector, harness trouble
(PCU PWB, high voltage
PWB, image density
sensor, photoconductor
unit, transfer unit,
developing unit)

Check &
Remedy

Check contact. Replace
the harness. Replace the
PWB.

Main
code

Sub

code

Title

Image data memory trouble

Display

Lamp/Message

Phenomenon Detail

The ICU image data
memory (SDRAM) cannot
be detected as 256MB or
more. The required
SDRAM capacity for the
model is not provided.

Section

ICU PWB

Case 1

Cause

The SDRAM of ICU PWB
is not installed. The
SDRAM of ICU PWB is
improperly installed.

Check &
Remedy

Check installation of the
SDRAM of ICU ASIC PWB.

Case 2

Cause

The SDRAM of ICU PWB
does not operate properly.

Check &
Remedy

Use SIM 60-01 to check
the capacity of the
SDRAM. Replace the
SDRAM of ICU PWB.

Case 3

Cause

ICU PWB abnormality

Check &
Remedy

Replace the ICU PWB.

Main
code

Sub

code

Title

ICU gate array trouble

Display

Lamp/Message

Phenomenon Detail

An abnormality occurs in
the ICU gate array.

Section

ICU PWB

Case 1

Cause

ICU PWB abnormality

Check &
Remedy

Replace the ICU PWB.

Case 2

Cause

Gate array (ASIC, FPGA)
abnormality on the ICU
PWB

Check &
Remedy

Replace the gate array on
the ICU PWB.

Main
code

Sub

code

Title

Image density sensor error/
Transfer charger error (Black)

Summary of Contents for AR-BC320

























































































































































































































































































































































Search results

Summary of Contents for AR-BC320

Reviews:

Sharp AR-BC320, Service Manual, Page: 250 / 344

Search results

Summary of Contents for AR-BC320

Reviews: