manualshive.com logo in svg

Sharp AR-BC320, Service Manual, Page: 311 / 344

Share
Download
Sharp AR-BC320 Service Manual Download Page 311

AR-BC320  ELECTRIC DIAGRAM  13 - 25

DPPD2

Paper transport sensor 2

Detects paper transport.

AR-D17/D18

DPPD3

Paper transport sensor 3

Detects paper transport.

AR-D17/D18

DRS

Reverse sensor

Detects that a document has been transported to the 
reverse sensor section.

RADF

DRSOL

Reverse solenoid

Switches the flapper in duplex operation.

RADF

DSWF

Front door open detection 

Detects opening of the front door.

Main machine

DSWL

Paper exit door open detection 

Detects opening of the paper exit door.

Main machine

DSWR

Paper feed door open detection 

Detects opening of the paper feed door.

Main machine

DTM

Transport motor

Transports a document on the document glass.

RADF

DTRC

Transport clutch 

Controls ON/OFF of the transport roller.

AR-D17/D18/D19

DUSTPTR

Punch dust full sensor

Detects punch dust full.

AR-F13

DWVR

Document width detection volume

Detects the document width on the tray.

RADF

EMPS

Empty sensor

Detects document presence on the paper feed tray.

RADF

ES

Entry port sensor

AR-F13

FAM

Bundle exit sensor

AR-F13

FDS

Front door sensor

AR-F13

FDSW

Front door switch 

AR-F13

FE

Bookbinding clock sensor

AR-F13

FES

Bookbinding paper senor

AR-F13

FFJM

Alignment motor (F)

AR-F13

FFM

Transport motor

AR-F13

FFSM

Stapler/Folding motor staple operation/
Paper folding operation

AR-F13

FHPS

Bookbinding HP sensor

AR-F13

FJHPS

Alignment HP sensor

AR-F13

FLM

Shift motor

AR-F13

FOS

ADF front open sensor

Detects opening of ADF.

RADF

FPM

Paddle motor oscillation guide drive, 
discharge to offset tray

AR-F13

FPNM

Punch motor

AR-F13

FPS

Bookbinding position sensor

AR-F13

FPSM

Puncher side registration motor

AR-F13

FRHPS

Bookbinding roller HP sensor

AR-F13

FRJM

Alignment motor (R)

AR-F13

FSM

Slide motor staple unit shift

AR-F13

FUSM

Fusing drive motor

Drives the fusing unit.

Main machine

GSS

Face up/down switch gate solenoid

Drives the face-up/down switch gate.

Main machine

HLTS1

Upper heat roller thermostat

Detects an abnormally high temperature to turn off the 
heater lamp.

Main machine

HLTS2

Lower heat roller thermostat

Detects an abnormally high temperature to turn off the 
heater lamp.

Main machine

HPOS

Offset home position sensor

Detects the offset home position.

Main machine

HUD

Humidity sensor

Detects the humidity.

Main machine

JS

Joint switch

AR-F13

LDD

Lower limit detector

AR-LC5

LE

Lift lock sensor

AR-F13

LEDONx

Paper size sensor

Detects the paper size.

AR-F13

LLLS

Lift lower limit sensor

AR-F13

LLM

Lift-up motor

AR-LC5

LLSW

Upper limit lock switch

AR-LC5

LPED

Paper detector

AR-LC5

LPFC

Paper clutch

AR-LC5

LPFD

Transport detector

AR-LC5

LPFM

Paper feed and transport motor

AR-LC5

LPFS

Pick-up solenoid

AR-LC5

LRES

Encoder sensor

AR-LC5

LTOD

Copier connection detector

AR-LC5

LTRC

Paper feed clutch

AR-LC5

LUD

Upper limit detector

AR-LC5

LUD1

1 cassette lift-up upper limit detection

Detects the paper upper limit position.

Main machine

LUM1

1 cassette  lift-up motor

Drives the lift plate.

Main machine

MHPS

Mirror home position sensor

Detects the scanner home position.

Main machine

Signal name

Name

Function/Operation

Section

Summary of Contents for AR-BC320

























































































































































































































































































































































Reviews:

No comments