Sharp AR-BC320, Service Manual, Page: 199 / 344

AR-BC320 SIMULATION 9 - 45
2. Enter the set value with the 10-key.
3. Press the [OK] key to set the fusing temperature set in
procedure 2.
(Display items)
(Items to be selected)
*1: Set to OFF when the printer half-tone process control
operation is abnormal. (Default setting: ON)
*2: Set to OFF to improve gradation of the printer monochrome
mode when the life of the photoconductor is nearly expired.
(Default setting: ON)
*3: When SIM 50-20 is used to adjust the image resist to the best
and the image resist adjustment is performed under the
following condition automatically, the best adjustment state
may be changed. To avoid this, set the adjustment item AR to
Disable.
When the adjustment item AR is set to Disable (ON), the
image resist adjustment is automatically performed under the
following conditions.
Normally set to ON condition.
*4: When the image registration automatic adjustment operation
is abnormal, it is judged as an error or not.
• After replacement of a toner cartridge
At every 8000 copies (total of print and copy)
(When, however, 8000 copies is reached during a job, the
operation is stopped after completion of the job.)
Display Content Set range
Default
100v
Series
120v
Series
200v
Series
China
only
A Normal paper HL1 set
value 70 – 230 170 175 175 170
B Normal paper HL2 set
value 30 – 200 140 140 140 140
C HL1 set value in ready
state 70 – 230 165 170 170 165
D HL2 set value in ready
state 30 – 200 120 120 120 120
E Heavy paper 1 HL1 set
value 70 – 230 170 175 175 170
F Heavy paper 1 HL2 set
value 70 – 230 135 136 136 135
G Heavy paper 2 HL1 set
value 70 – 230 175 175 175 175
H Heavy paper 2 HL2 set
value 70 – 230 145 145 145 145
I OHP1 HL1 set value 70 – 230 170 170 170 170
J OHP1 HL2 set value 70 – 230 155 155 155 155
K OHP2 HL1 set value 70 – 230 170 170 170 170
L OHP2 HL2 set value 70 – 230 155 155 155 155
M Envelope HL1 set value 70 – 230 180 180 180 180
N Envelope HL2 set value 70 – 230 145 145 145 145
O Temperature set value
in pre-heating 70 – 200 143 143 143 143
P Set temperature at
which print is ready by
heating up from the
preheat mode. (Black
and white copy mode) 70 – 200 165 165 165 165
Q Set temperature at
which the fusing motor
starts rotation in
warming up operation. 70 – 200 155 155 155 155
R When set to “1,” the
upper and the lower
heat rollers are ready
for print only when they
reach the specified
temperature. (Used
when abnormal fusing
occurs under low
temperature
environment.)
When set to “0,” the
operation is performed
in the normal mode.
That is, print is ready
when the upper heat
roller reaches the
specified temperature.) 0 – 1 0 0 0 0
44
44 -1
Purpose Setting
Function
(Purpose) Used to set enable/disable of correction operations
in the image forming (process) section.
Section Process (Photoconductor, developing, transfer,
cleaning)
Item Operation
Operation/
Procedure 1. Select the process item to enable the operation.
2. Press the [EXECUTE] key. (The operations of all
process items must be enabled.)
Display Content
HV Image forming section correction (Process
correction)
(High-density image density correction)
HT Half-tone image density correction
HT (PRT) *1 Half-tone image density correction (Printer)
TC Transfer output correction
RRM RRM speed correction
MD Photoconductor membrane decrease (sensitivity/
potential) correction
MD
(PRT_BK) *2 Photoconductor membrane decrease (sensitivity/
potential) correction (Printer: monochrome)
AR Image resist auto adjustment *3
AR CHK Image resist auto adjustment error judgment
YES/NO *4
44 -2
Purpose Adjustment
Function
(Purpose) Black image density sensor adjustment
Section Process (Transfer)
Item Operation
Operation/
Procedure 1. Press the [EXECUTE] key.
The amplifier gain adjustment of the black image
density sensor is automatically performed.
After completion of the adjustment, the result is
displayed and the [EXECUTE] key display returns
to the original state.