Sharp AR-BC320 Service Manual Download Page 239

Page: 239 / 344

AR-BC320 MAINTENANCE LIST 10 - 4

C. Transfer section

: Check (Clean, replace, or adjust as necessary.)

❍

: Clean

▲

: Replace

∆

: Adjust

✩

: Lubricate

❏

: Shift position

Unit

Name

No.

Part name

When

calling

50K

100K

150K

200K 250K

300K

350K 400K

Remark

Transfer
section

Transfer belt

▲

Replace at 100K or
within 2 years.

Transfer roller

▲

Transfer belt cleaning blade

▲

Replace at 100K or
within 2 years.

Transfer discharge sheet

❍

Transfer belt cleaning roller

▲

Transfer drive roller

Transfer follower roller

Transfer cleaning brush

Sensors

Waste toner tank unit

▲

When waste toner full
is detected.

Transfer belt unit

▲

Replace the unit at
100K or within 2 years.

Summary of Contents for AR-BC320

























































































































































































































































































































































Search results

Summary of Contents for AR-BC320

Reviews:

Sharp AR-BC320, Service Manual, Page: 239 / 344

Search results

Summary of Contents for AR-BC320

Reviews: