Sharp AR-BC320 Service Manual Download Page 37

Page: 37 / 344

AR-BC320 EXTERNAL VIEW AND INTERNAL STRUCTURE 6 - 8

G. Sensors, switches and heaters

No.

Parts

Code, signal

name

Type

Name

Function

O/C open/close sensor

Detects open/close of the document cover. (A timing signal of
document size detection is produced.)

OCSW

Photo sensor (Photo
transmission)

Offset home position sensor

Detects the offset home position.

HPOS

Photo sensor (Photo
transmission)

Paper exit tray full detection

Detects full of the face down paper exit tray.

TFD2

Photo sensor (Photo
transmission)

Mirror home position sensor

Detects the scanner home position.

MHPS

Photo sensor (Photo
transmission)

Toner empty sensor (Y)

Detects toner empty (Y).

TES_Y

Photo sensor (Photo
transmission)

Toner empty sensor (M)

Detects toner empty (M).

TES_M

Photo sensor (Photo
transmission)

Toner empty sensor (C)

Detects toner empty (C).

TES_C

Photo sensor (Photo
transmission)

Toner empty sensor (K)

Detects toner empty (K).

TES_K

Photo sensor (Photo
transmission)

No. 1 paper transport sensor

Detects paper in front of the resist roller.

PPD1

Photo sensor (Photo
transmission)

Paper feed door open detection

Detects open/close of the paper feed door.

DSWR

Micro switch

Manual feed paper empty detection

Detects paper empty on the paper tray.

MPED

Photo sensor (Photo
transmission)

Manual feed tray pulling out detection 2

Detects the paper tray position.

MTOP2

Contact switch

No. 1 cassette paper size detection 1

Detects the paper size set by the paper size set blocks.

C1SS1

Contact switch

No. 1 cassette paper size detection 2

Detects the paper size set by the paper size set blocks.

C1SS2

Contact switch

No. 1 cassette paper size detection 3

Detects the paper size set by the paper size set blocks.

C1SS3

Contact switch

No. 1 cassette paper size detection 4

Detects the paper size set by the paper size set blocks.

C1SS4

Contact switch

No. 1 cassette lift-up position detection 1

Detects the lift plate position. (Detects the paper quantity.)

C1PD1

Photo sensor (Photo
transmission)

Manual feed paper length detection 2

Detects the paper length.

MPLD2

Photo sensor (Photo
transmission)

Manual feed tray pulling out detection 1

Detects the paper tray position.

MTOP1

Contact switch

Manual feed paper length detection 1

Detects the paper length.

MPLD1

Photo sensor (Photo
transmission)

Humidity sensor

Detects the ambient humidity.

HUD

—

Paper tray
lift-up unit

Front / right side / top view

Summary of Contents for AR-BC320

























































































































































































































































































































































Search results

Summary of Contents for AR-BC320

Reviews:

Sharp AR-BC320, Service Manual, Page: 37 / 344

Search results

Summary of Contents for AR-BC320

Reviews: