manualshive.com logo in svg

Sharp AR-BC320, Service Manual, Page: 271 / 344

Share
Download
Sharp AR-BC320 Service Manual Download Page 271

AR-BC320  TROUBLESHOOTING  11 - 24

Main 
code

Sub 

code

Title

EEPROM read/write error (SCN)

U2

80

Display

Lamp/Message

Phenomenon Detail

EEPROM version error
EEPROM write error

Section

—

Case 1

Cause

EEPROM trouble, 
Insertion of EEPROM 
which is not initialized or 
defective.

Check & 
Remedy

1. Check that the 

EEPROM is properly 
inserted.

2. Use SIM 16 to cancel 

the error.

Case 2

Cause

SCN PWB EEPROM 
access circuit trouble

Check & 
Remedy

1. To prevent against 

deletion of the counter 
data and the adjustment 
data, record them with 
the simulation. (When a 
printer option is 
installed, use SIM 22-1 
to record the counter 
data and the adjustment 
data.)

2. Replace the SCN PWB.
3. Use SIM 16 to cancel 

the error.

Main 
code

Sub 

code

Title

Adjustment value check sum error 
(SCN)

U2

81

Display

Lamp/Message

Phenomenon Detail

EEPROM (SCN) check 
sum error

Section

—

Case 1

Cause

EEPROM trouble

Check & 
Remedy

1. Check that the 

EEPROM is properly 
inserted.

2. Use SIM 16 to cancel 

the error.

Case 2

Cause

SCN PWB EEPROM 
access circuit trouble

Check & 
Remedy

1. To prevent against 

deletion of the counter 
data and the adjustment 
data, record them with 
the simulation. (When a 
printer option is 
installed, use SIM 22-1 
to record the counter 
data and the adjustment 
data.)

2. Replace the SCN PWB.
3. Use SIM 16 to cancel 

the error.

Main 
code

Sub 

code

Title

EEPROM read/write error (PCU)

U2

90

Display

Lamp/Message

Phenomenon Detail

EEPROM version error
EEPROM write error

Section

—

Case 1

Cause

EEPROM trouble,
Insertion of EEPROM 
which is not initialized or 
defective.

Check & 
Remedy

1. Check that the 

EEPROM is properly 
inserted.

2. Use SIM 16 to cancel 

the error.

Case 2

Cause

PCU PWB EEPROM 
access circuit trouble

Check & 
Remedy

1. To prevent against 

deletion of the counter 
data and the adjustment 
data, record them with 
the simulation. (When a 
printer option is 
installed, use SIM 22-1 
to record the counter 
data and the adjustment 
data.)

2. Replace the PCU PWB.
3. Use SIM 16 to cancel 

the error.

Main 
code

Sub 

code

Title

Adjustment value check sum error 
(PCU)

U2

91

Display

Lamp/Message

Phenomenon Detail

EEPROM (PCU) check 
sum error

Section

—

Case 1

Cause

EEPROM trouble

Check & 
Remedy

1. Check that the 

EEPROM is properly 
inserted.

2. Use SIM 16 to cancel 

the error.

Case 2

Cause

Control circuit freeze 
caused by noises, PCU 
PWB EEPROM access 
circuit trouble

Check & 
Remedy

1. To prevent against 

deletion of the counter 
data and the adjustment 
data, record them with 
the simulation. (When a 
printer option is 
installed, use SIM 22-1 
to record the counter 
data and the adjustment 
data.)

2. Replace the PCU PWB.
3. Use SIM 16 to cancel 

the error.

Summary of Contents for AR-BC320

























































































































































































































































































































































Reviews:

No comments