manualshive.com logo in svg

Sharp AR-BC320, Service Manual, Page: 266 / 344

Share
Download
Sharp AR-BC320 Service Manual Download Page 266

AR-BC320  TROUBLESHOOTING  11 - 19

Main 
code

Sub 

code

Title

Thermistor open (HL1)

H2

00

Display

Lamp/Message

Phenomenon Detail

Thermistor open

Section

Fusing

Case 1

Cause

Disconnection of the fusing 
section connector

Check & 
Remedy

Check the connector and 
the harness between the 
thermistor and the control 
PWB.

Case 2

Cause

The fusing unit is not 
installed.

Check & 
Remedy

Install the fusing unit.

Case 3

Cause

Thermistor trouble, control 
PWB trouble, AC power 
supply trouble

Check & 
Remedy

Replace the thermistor or 
the control PWB. Check 
the AC power supply.

Main 
code

Sub 

code

Title

Thermistor open (HL2)

H2

01

Display

Lamp/Message

Phenomenon Detail

Thermistor open

Section

Fusing

Case 1

Cause

Disconnection of the fusing 
section connector

Check & 
Remedy

Check the connector and 
the harness between the 
thermistor and the control 
PWB.

Case 2

Cause

The fusing unit is not 
installed.

Check & 
Remedy

Install the fusing unit.

Case 3

Cause

Thermistor trouble, control 
PWB trouble, AC power 
supply trouble

Check & 
Remedy

Replace the thermistor or 
the control PWB. Check 
the AC power supply.

Main 
code

Sub 

code

Title

Fusing section high temperature 
trouble (THS1)

H3

00

Display

Lamp/Message

Phenomenon Detail

The fusing temperature 
exceeds 230°C.

Section

Fusing

Common

Check 

Use SIM 5-2 to check the 
heater lamp flashing 
operation.

Case 1

Cause

The heater lamp flashes 
properly with SIM 5-2. 
Thermistor trouble, 
disconnection of the fusing 
section connector

Check & 
Remedy

Check the thermistor and 
its harness. Cancel the 
error with SIM 14.

H3

00

Case 2

Cause

The heater lamp keeps ON 
with SIM 5-2.
Control PWB trouble, AC 
power supply trouble

Check & 
Remedy

Check the AC PWB and 
the control PWB lamp 
control circuit.
Cancel the error with SIM 
14.

Main 
code

Sub 

code

Title

Fusing section high temperature 
trouble (THS2)

H3

01

Display

Lamp/Message

Phenomenon Detail

The fusing temperature 
exceeds 230°C.

Section

Fusing

Common

Check 

Use SIM 5-2 to check the 
heater lamp flashing 
operation.

Case 1

Cause

The heater lamp flashes 
properly with SIM 5-2.
Thermistor trouble, 
disconnection of the fusing 
section connector

Check & 
Remedy

Check the thermistor and 
its harness. Cancel the 
error with SIM 14.

Case 2

Cause

The heater lamp keeps ON 
with SIM 5-2. AC power 
supply trouble, control 
PWB trouble

Check & 
Remedy

Check the AC PWB and 
the control PWB lamp 
control circuit.
Cancel the error with SIM 
14.

Main 
code

Sub 

code

Title

Fusing section low temperature 
trouble (HL1)

H4

00

Display

Lamp/Message

Phenomenon Detail

The fusing temperature is 
not reached within the 
specified time after turning 
on the power relay.

Section

Fusing

Common

Check

Use SIM 5-2 to check the 
heater lamp flashing 
operation.

Case 1

Cause

The heater lamp flashes 
properly with SIM 5-2. 
Thermistor trouble, PCU 
PWB (thermistor input 
circuit) trouble

Check & 
Remedy

Check the thermistor and 
its harness. Check the 
PCU PWB thermistor input 
circuit.
Cancel the error with SIM 
14.

Main 
code

Sub 

code

Title

Fusing section high temperature 
trouble (THS1)

Summary of Contents for AR-BC320

























































































































































































































































































































































Reviews:

No comments