manualshive.com logo in svg

Sharp AR-BC320, Service Manual, Page: 259 / 344

Share
Download
Sharp AR-BC320 Service Manual Download Page 259

AR-BC320  TROUBLESHOOTING  11 - 12

Main 
code

Sub 

code

Title

Toner empty sensor abnormality 
(Magenta)

F2

42

Display

Lamp/Message

Phenomenon Detail

Toner empty sensor output 
abnormality

Section

Cartridge

Case 1

Cause

Connector harness 
trouble, connector 
disconnection

Check & 
Remedy

1. Check connection of the 

toner empty sensor. 

→

 

Connect it properly.

2. Check connection of the 

connector harness to 
the PCU PWB. 

→

 

Connect it properly.

3. Check connection of the 

cartridge. 

→

 Connect it 

properly.

4. Check for disconnection 

of the harness. 

→

 

Replace the harness.

Case 2

Cause

Cartridge trouble

Check & 
Remedy

Replace the cartridge. 

Main 
code

Sub 

code

Title

Toner empty sensor abnormality 
(Yellow)

F2

43

Display

Lamp/Message

Phenomenon Detail

Toner empty sensor output 
abnormality

Section

Cartridge

Case 1

Cause

Connector harness 
trouble, connector 
disconnection

Check & 
Remedy

1. Check connection of the 

toner empty sensor. 

→

 

Connect it properly.

2. Check connection of the 

connector harness to 
the PCU PWB. 

→

 

Connect it properly.

3. Check connection of the 

cartridge. 

→

 Connect it 

properly.

4. Check for disconnection 

of the harness. 

→

 

Replace the harness.

Case 2

Cause

Cartridge trouble

Check & 
Remedy

Replace the cartridge.

Main 
code

Sub 

code

Title

Black image density sensor 
trouble (Transfer belt surface 
reflection ratio abnormality)

F2

44

Display

Lamp/Message

Phenomenon Detail

Before starting process 
control, the transfer belt 
surface is scanned with the 
image density sensor to 
adjust the sensor gain so 
that the output becomes a 
fixed value. However, 
when the sensor gain is 
changed, the output is not 
within the specified range.

Section

—

Common

Check

Use SIM 44-2 to adjust the 
process control sensor 
gain.

Case 1

Cause

When "Error" occurs in 
SIM 44-2:
1. Dirt/defect of the image 

density sensor

2. Disconnection of the 

harness between the 
PCU PWB and the 
image density sensor

3. Calibration plate 

solenoid operation 
trouble

Check & 
Remedy

1. Clean/replace the 

image density sensor.

2. Connect/replace the 

harness between the 
PCU PWB and the 
image density sensor.

3. Replace the calibration 

plate solenoid.

Case 2

Cause

When SIM 44-2 is 
completed:
1. Insufficient cleaning of 

the transfer belt.

Check & 
Remedy

1. Check the transfer belt 

surface.

Main 
code

Sub 

code

Title

Color image density sensor 
trouble (Calibration plate surface 
reflection ratio abnormality)

F2

45

Display

Lamp/Message

Phenomenon Detail

Before starting process 
control, the calibration 
plate surface is scanned 
with the image density 
sensor to adjust the sensor 
gain so that the output 
becomes a fixed value. 
However, when the sensor 
gain is changed, the output 
is not within the specified 
range.

Section

—

Common

Check 

Use SIM 44-2 to adjust the 
process control sensor 
gain.

Summary of Contents for AR-BC320

























































































































































































































































































































































Reviews:

No comments