manualshive.com logo in svg

Sharp AR-BC320, Service Manual, Page: 170 / 344

Share
Download
Sharp AR-BC320 Service Manual Download Page 170

AR-BC320  SIMULATION  9 - 16

67

1

Used to check the operations of 
printer DRAM read/write.

Operation test/
check

Printer

Operation

11

Used to set the printer parallel I/
F SELECT IN signal.

Setting

Printer

Operation

14

Used to perform version up of 
the firmware. (Printer)

Version up

Firmware (Printer)

Operation

17

Used to clear NVRAM. (Printer)

Data clear

Printer

Others

18

Used to clear the Flash data. 
(Printer)

Data clear

Printer

Others

24

Used to adjust half-tone density 
of the printer engine 
automatically.

Adjustment

25

Printer engine color balance 
manual correction: PG print 
(Used to perform a fine 
adjustment of color from the 
adjustment of SIM 67-24.)

Adjustment

26

Used to select the target value 
of the referenced scanner in the 
printer engine automatic density 
adjustment. (The target value 
set with SIM 67-24 and the gray 
balance can be adjusted.)

Adjustment

27

Used to display and register the 
scanner target value (for 
servicing) of the printer engine 
automatic density adjustment. 
(Conforms to the service button 
of SIM 67-24. (The serviceman 
can scan the target value.))

Adjustment

28

Used to reset the scanner target 
value (for servicing) in the printer 
engine automatic density 
adjustment to the standard 
value. (Reset to the standard 
value of SIM67-27. (The value is 
reset to the factory setting.))

Adjustment

29

Used to set the printer screen 
mode.

Setting

40

Used to copy the scanner 
destination. (Flash writing)

Setting

Flash ROM (Scanner)

Data

Writing

Code

Function (Purpose)

Purpose

Section

Item

Main Sub

Summary of Contents for AR-BC320

























































































































































































































































































































































Reviews:

No comments